AWWA C210-2003 中文版 液態無溶劑環氧樹脂涂層.doc

《AWWA C210-2003 中文版 液態無溶劑環氧樹脂涂層.doc》由會員分享，可在線閱讀，更多相關《AWWA C210-2003 中文版 液態無溶劑環氧樹脂涂層.doc（23頁珍藏版）》請在裝配圖網上搜索。

AWWA C210 Liquid-Epoxy Coating Systems for the Interior and Exterior of Steel AWWA Standard? AWWA標準 This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administrative information normally contained in specifications. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA publication of a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. AWWA standards are intended to represent a consensus of the water supply industry that the product described will provide satisfactory service. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the classified advertising section of Journal AWWA. The action becomes effective on the first day of the month following the month of Journal AWWA publication of the official notice. 此文件是美國自來水廠（AWWA）標準，不是規范。AWWA只描述了最低要求，不包含一般規范中所需的工程和管理規范信息。AWWA標準包含由用戶自己評判的選擇，除非用戶指定標準，否則就不充分定義產品或者服務。AWWA標準，所做試驗和認證不針對特定型號和產品，也不授權認同任何產品。使用AWWA標準完全自愿。AWWA標準旨在代表水供應行業的一致意見，使產品能夠獲得客戶的滿意。一旦AWWA修改或者撤銷某些條款，AWWA會在廣告頁面的第一頁發布正式的通知。修改的條款會在發布正式通知后下一個月的第一天生效。 ? American National Standard 美國國家標準 An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encouraged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. 美國國家標準包含了對標準范圍和要求的一致意見。各項美國國家標準旨在指導幫助廠商，消費者，和廣大群眾。不管是否同意標準，美國國家標準的存在從任何一方面來說都不會排斥任何人生產，銷售，購買或者使用與標準不符合的產品。美國國家標準定期審查，用戶需要注意獲取最新的標準。我們鼓勵那些按照美國國家標準生產的廠家，在廣告，促銷產品上打上符合美國國家標準的標示。 CAUTION NOTICE: The American National Standards Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, 25 W. 43rd St., Fourth Floor, New York, NY 10036-7406; (212) 642-4900. 警示通知：美國國家標準協會在標準的封面頁標上日期就表示標準通過ANSI的認證。美國國家標準可以隨時修改或撤銷。ANSI程序要求必須在標準出版5年內對標準重審，修改或撤銷。美國國家標準的業主可以通過撥打(212)642-4900或者寫信給美國國家標準協會，地址：紐約市西43大街第四層樓25號,郵編: NY 10036-7406 來獲得所有標準的最新信息。 ? Contents 目錄 Foreword 前言 I Introduction 簡介.........................................? ix I.A Background 背景...........................................ix I.B History 歷史.................................. ............ix I.C Acceptance 認可............................................ix II Special Issues 特別說明......................................x III Use of This Standard 使用此標準.............................xi III. A Purchaser Options and Alternatives 業主的選擇和代替品….xi III.B Modification to Standard 標準修改........................xii IV Major Revisions 主要修訂.....................................xii V Comments 評論.................................................xii Standard 標準 1General 總則 1.1Scope 范圍..................................................1 1.2Purpose 目的................................................2 1.3Application 使用............................................2 2References 參考...............................................2 3Definitions ?定義.............................................3 4Requirements 要求 4.1Equipment 設備...............................................4 4.2Quality and Safety質量和安全.................................4 4.3Coating System 噴涂系統.......................................4 4.4Coating Application 噴涂應用..................................6 4.5Coating Repair修補噴涂........................................8 4.6Welded Field Joints 焊接管件...................................8 4.7Coating Special Pipe Connections and Appurtenances噴涂特殊管件和附件.........................9 4.8Field Procedures 現場施工…………………………………………………10 5Verification 驗收 5.1Inspection and Testing 檢驗和測試..............................11 5.2Performance Testing of Laboratory-Applied Epoxy Coating System 實驗室噴涂系統性能測試.....12 5.3Rejection 不通過...............................................12 6Delivery 運輸 6.1Marking 標示...................................................13 6.2Packaging, Handling, Stacking, and Storage 包裝，搬運，堆放，存儲................................................................13 6.3Affidavit of Compliance 服從申明................................13 Table 表格 1Coated Pipe Inspection Tests 涂塑管檢測..........................5 2Performance Requirements of Laboratory-Applied Epoxy Coating System.實驗室噴涂系統性能測試5 ? Foreword 前言 This foreword is for information only and is not a part of AWWA C210. 前言只是相關資料，并不作為AWWA C210標準的一部分。 I. Introduction.簡介 I.A. Background. This standard was developed to provide information for the use of liquid-epoxy coatings for the exterior coating and interior lining of steel water pipe. The standard has been revised periodically to meet increasingly demanding environmental and health-effects regulations and to modify procedures based on technological advances. I.A.背景。此標準提供了鋼制水管內外涂液體環氧樹脂的相關信息。標準定期修改以符合日益苛求的環境和安全規范要求并根據科技發展修改相關方法。 I.B. History. The first edition of AWWA C210 was approved for issue in May 1978, under the title, “Coal-Tar Epoxy Coating System for the Interior and Exterior of Steel Water Pipe.” The second and third editions were approved on June 10, 1984, and June 18, 1992, respectively, and published under the title, “Liquid-Epoxy Coating Systems for the Interior and Exterior of Steel Water Pipelines.” The fourth edition of ANSI/AWWA C210 was approved by the AWWA Board of Directors on June 15, 1997. This edition was approved by the AWWA Board of Directors on Jan. 19, 2003. I.B. 歷史。第一版AWWA C210與1978年五月批準通過，標準名為：鋼制水管內外煤焦油環氧涂層系統。第二版和第三版分別與194年6月10號和6月18號批準，標準名為：鋼制水管內外涂液體環氧樹脂涂層系統。第四版ANSI/AWWA C210 于1997年6月15號獲得AWWA董事會批準，此版本是2003年1月19日通過AWWA批準。 I.C.? Acceptance. In May 1985, the US Environmental Protection Agency (USEPA) entered into a cooperative agreement with a consortium led by NSF International (NSF) to develop voluntary third-party consensus standards and a certification program for all direct and indirect drinking water additives. Other members of the original consortium included the American Water Works Association Research Foundation (AWWARF) and the Conference of State Health and Environmental Managers (COSHEM). The American Water Works Association (AWWA) and the Association of State Drinking Water Administrators (ASDWA) joined later. I.C.? 認可。1985年5月，美國環境保護署（USEPA）與參與由NSF國際領銜的機構大成合作性協議，共同制定自愿性的第三方標準和所有直接和非直接飲用水添加劑的認證程序。機構里的原先成員包括美國水協研究基金會（AWWARF）和國家健康和環境管理中心，之后美國水力協會（AWWA）和國家飲用水管理協會（ASDWA）也加入其中。 In the United States, authority to regulate products for use in, or in contact with, drinking water rests with individual states.在美國，權威部門對運輸飲用水或與飲用水接觸的產品的管理主要依靠各個州政府。 * Local agencies may choose to impose requirements more stringent than those required by the state. To evaluate the health effects of products and drinking water additives from such products, state and local agencies may use various references, including 地方機構可能執行比國家更加嚴格的要求對這些影響健康的產品或者產生飲用水添加劑的產品評估，并且地方機構可能參考各種不同的標準，包括： ?*Persons in Canada, Mexico, and non-North American countries should contact the appropriate authority having jurisdiction. 加拿大，墨西哥和非北美的國家的人民需要咨詢當地相關法律部門。 1. An advisory program formerly administered by USEPA, Office of Drinking Water, discontinued on Apr. 7, 1990. USEPA 飲用水辦公室執行的指導性程序，于1990年4月7號終止。 2. Specific policies of the state or local agency. 國家或者地方特定的政策。 3. Two standards developed under the direction of NSF, ANSI NSF和ANSI頒布的兩個標準。 */NSF? 60, Drinking Water Treatment Chemicals—Health Effects, and ANSI/NSF 61, Drink-??? ing Water System Components—Health Effects. NSF 60 飲用水化學處理品對健康的影響和ANSI/NSF 61飲用水系統部件對健康的影響。 4. Other references, including AWWA standards, Food Chemicals Codex, Water Chemicals Codex,? and other standards considered appropriate by the state or local agency. 其他參考資料，包括美國自來水廠協會標準，食品化學法典，水化學品法典，和州或地方機構頒布的其他標準。 Various certification organizations may be involved in certifying products in accordance with ANSI/NSF 61. Individual states or local agencies have authority to accept or accredit certification organizations within their jurisdiction. Accreditation of certification organizations may vary from jurisdiction to jurisdiction. 其他認證機構也可能參與了ANSI/NSF61的認證工作，各個州和地方機構在他們的權利范圍內有權利接受或任命認證機構。根據司法權利不同，每個認證機構的任命不一樣。 Annex A, “Toxicology Review and Evaluation Procedures,” to ANSI/NSF 61 does not stipulate a maximum allowable level (MAL) of a contaminant for substances not regulated by a USEPA final maximum contaminant level (MCL). The MALs of an unspecified list of “unregulated contaminants” are based on toxicity testing guidelines (noncarcinogens) and risk characterization methodology (carcinogens).Use of Annex A procedures may not always be identical, depending on the certifier. 附件A， ANSI/NSF61中的毒理學評論和評價程序并沒有制定污染物的最大容許量，USEPA沒有規定最大污染物等級。未列入規定的最大容許量的污染物的確定基于毒理學測試（非致癌物）和風險特征學（致癌物）的指導。每個測試者有可能得到唯一的一種測試結果。 AWWA C210 does not address additives requirements. Thus, users of this standard should consult the appropriate state or local agency having jurisdiction in order to AWWQ C210沒有注明添加物要求，所以，這個標準的使用者需要咨詢具有司法權的相關州和當地機構為了： 1. Determine additives requirements, including applicable standards. 決定添加物要求，包括適用的標準。 2. Determine the status of certifications by all parties offering to certify products for contact with, or treatment of, drinking water. 決定各方認證的證書狀態，提供方法認證水處理方法。 3. Determine current information on product certification. 決定產品認證信息。 II. Special Issues.特別事宜。 This standard provides guidance to the water industry in selecting and evaluating liquid-epoxy coatings for use in potable water service and sets minimum requirements for linings and coatings used on steel water pipe in the potable water supply industry. 此標準旨在指導選擇和評價液體環氧樹脂在可飲用水上的使用，并設定運送飲用水鋼制管道的襯里和涂層的最低標準。 Users of this standard are advised to consider additional lining thickness for pipe that handles water containing higher than normal levels of particulates or that operates at higher than normal velocities. A penstock carrying mountain water would be a viable example. The required finished coating thickness shall be specified by the purchaser. The specified thickness should not exceed the maximum recommended by the coating manufacturer. 如果管道水中含有的異物比正常情況下多，或者水流速度較高的情況下，此標準的使用者建議需要考慮管道襯里的厚度。山泉水管道系統就是一個例子。業主需要確定涂層的厚度，但是厚度不應超過涂層生產商的建議厚度。 Soluble salts and other inorganic contaminants on a prepared steel surface have been known to influence coating performance. Procedures for determining the presence of these contaminants as well as the method of quantifying them are currently being evaluated by technical organizations serving the paint industry. 可溶性鹽和其他無機污染物會影響鋼管的涂層性能。測定污染物是否存在以及量化污染物的任務主要由油漆工業的技術機構負責。 If an extended period of aboveground storage of the coated pipe is anticipated, consideration should be given to the ability of the coating to resist degradation by ultraviolet light and other atmospheric and environmental conditions. The purchaser should consult the manufacturer for specific conditions and limitations. 如果預期涂塑管需要地面存放超過指定時間，則需要考慮到涂層在紫外線和其他大氣和環境條件影響下的退化問題，業主需要咨詢生產商涂塑管存放的特定條件和限制。 This standard does not describe materials and procedures that may be required for difficult conditions, such as those encountered in construction of some submarine lines, casing pipe, river crossings, and rocky areas. 此規范沒有描述在艱難的條件下材料的選用和使用程序，比如說在海岸邊，鉆管時，河道交叉口，巖石地區。 III. Use of This Standard. AWWA has no responsibility for the suitability or compatibility of the provisions of this standard to any intended application by any user. Accordingly, each user of this standard is responsible for determining that the standard’s provisions are suitable for and compatible with that user’s intended application. III.標準的使用。AWWA對標準是否適應或符合使用者的要求不付責任，而相應的，每個使用者需要自己承擔責任決定此標準是否適用和符合要求。 III. A. Purchaser Options and Alternatives. The following items should be provided in the purchaser’s specifications: 業主的選擇和備選方案，業主規范中需要提供如下要求： 1. Standard used—that is, ANSI/AWWA C210, Standard for Liquid-Epoxy Coating Systems for the Interior and Exterior of Steel Water Pipelines, of latest revision. 選用的規范—即 ANSI/AWWA C210鋼制水管用內外層液體環氧樹脂噴涂系統,最新版。 2. Any exceptions to the standard. 有別于標準的特別要求。 3. Diameter, length, and location of pipeline. 管道的直徑，長度和安裝地點。 4. Affidavit of compliance, if required (Sec. 6.3). 服從申明，如需要（Sec6.3） 5. Certification (Sec. 4.2.2).證書（Sec.4.2.2） 6. Government regulations (Sec. 4.2.3).政府法規（Sec.4.2.3） 7. The minimum and maximum dry film thickness (DFT) of the lining or coating (Sec.4.3.2).襯里或者涂層的最薄和最厚的干膜厚度（DFT） 8. Safety and environmental regulations (Sec. 4.2).安全和環境法規（Sec.4.2） 9. Visual comparative standard for surface preparation (Sec. 4.4.2.3). 表面處理視覺比較標準(Sec.4.4.2.3) 10. Profile determination (Sec. 4.4.2.5).切面要求（Sec.4.4.2.5） 11. Requirements for coating application (Sec. 4.4.3).噴涂要求(Sec.4.4.3) 12. Holdback for field welds (Sec. 4.4.3.2).現場焊接要求（Sec4.4.3.2） 13. Requirements for field joint coating (Sec. 4.6).現場連接件的噴涂要求 14. Coating requirements for special connections and appurtenances (Sec.4.7).特殊連接件和附加的噴涂要求。 15. Requirements for material inspection and rejection (Sec. 5.1 and 5.3).材料驗收和拒收要求（Sec.5.1和5.3） 16. Requirements for adhesion testing of coating (Sec. 5.1.6). 噴涂的黏性測試（Sec.5.1.6） 17. Provisions for bedding and trench backfill (Sec. 4.8.3). 墊層和溝槽回填要求。（Sec.4.8.3） 18. Packaging, handling, stacking, and storage (Sec. 6.2).包裝，運輸，堆放，存儲(Sec.6.2) 19. The purchaser should state whether compliance with ANSI/NSF 61 Drinking Water System Components—Health Effects is required, in addition to the requirements of the Safe Drinking Water Act.業主需要聲明除了要符合安全飲用水法案之外還是否需要符合ANSI/NSF61 飲用水系統部件對健康影響規范的要求 III.B. Modification to Standard. Any modification to the provisions, definitions, or terminology in this standard must be provided in the purchaser’s specifications. III.B標準的修改。任何對標準條款，定義，屬于的修改必須反映在業主的規范中。 IV. Major Revisions. Major changes made to the standard in this revision include the following: IV.重大修改。重大修改指如下幾點： 1. Physical and performance requirements have been divided into two separate tables.物理和性能要求放在兩張表中。 2. Replaced v-cut adhesion test with ASTM D3359 (Method A). 用ASTM D3359（方法A）替換V-cut 黏性測試。 3. Sec. 4.4.2.6, Surface Inspection, was revised. Sec.4.4.2.6改變表面測試 4. Sec. 4.4.3.6, Cure, was revised. Sec. 4.4.3.6, 修復方法改變。 5. Sec. 5.1, Inspection, was revised. Sec. 5.1,檢驗方法改變。 6. Sec. 5.2, Performance Testing of Laboratory-Applied Epoxy Coating System, was added. Sec. 5.2 增加實驗室涂塑系統性能測試要求。 7. Sec. 6.3, Affidavit of Compliance, was revised. Sec.6.3 更改服從申明 V. Comments. If you have any comments or questions about this standard, please contact the AWWA Volunteer and Technical Support Group, FAX (303) 795-7603, or write to the group at 6666 West Quincy Avenue, Denver, CO 80235-3098, or by e-mail at?standards@awwa.org. V．評論。如果對此標準有什么評價或疑問，請聯系AWWA志愿工作者和技術支持部門，Fax(303) 795-7603，或寫信到丹佛市，昆西西路6666 號，郵箱號80235-3098，或者Email:?standards@awwa.org. ? ?Liquid-Epoxy Coating Systems for the Interior and Exterior of Steel Water Pipelines 鋼制水管用內外層液體環氧樹脂噴涂系統 ? SECTION 1: GENERAL 總則 Sec. 1.1Scope 范圍 This standard sets minimum requirements for shop- and field-applied, liquid-epoxy interior linings and exterior coatings used in the potable-water-supply industry for steel water pipelines installed underground or underwater, under normal construction conditions. 對于埋地，水下或者一般施工情況下使用的飲用水給水涂塑鋼管，此標準對鋼管涂層，不管是工廠噴涂還是現場噴涂的內外液體環氧涂層設定了最低標準。 1.1.1 Conditions not described in this standard. The coating systems described in this standard are not intended for use on pipe that will be bent after the coating or lining system has been applied. 1.1.1 標準中沒有敘述的條件。噴涂系統不適用于那些噴涂后需要折彎的管道。 1.1.2 Coating and lining systems. Unless specified otherwise by the purchaser, the coating and lining systems may consist of any of the following three types: 1.12 噴涂和襯里，除非業主特別說明，噴涂和襯里一般有以下三種形式： (1) a two-part, chemically cured epoxy primer and one or more coats of a different two-part, chemically cured epoxy topcoat; (2) two or more coats of the same two-part, chemically cured epoxy coating, in which case the first coat shall be considered as the prime coat; or (3) a single coat of a two-part, chemically cured epoxy coating. （1）一層雙組份化學固化的環氧底漆和一層或多層雙組份化學固化的環氧面漆；（2）兩層或多層雙組份化學固化的環氧面漆，其中第一層可以作為底漆；（3）單層雙組份化學固化的環氧面漆。 1.1.2.1 Maximum temperature. All AWWA steel pipe coating standards are based on the maximum service temperature of potable water. The purchaser shall consult the coating manufacturer for conditions and limitations. 1.1.2.1最高溫度。所有AWWA鋼管涂層標準都按照飲用水的最高溫度指定，但是業主仍需要咨詢廠家的涂層條件和限制。 Sec. 1.2Purpose 目的 The purpose of this standard is to provide the minimum requirements for liquid-epoxy coating systems for the interior and exterior of steel water pipelines, including material, application, inspection, testing, performance requirements, handling, and packaging requirements. 此標準旨在提供鋼制水管用內外層液體環氧樹脂的最低要求，包括材質，應用，檢驗，測試，性能要求，運輸，包裝等要求。 Sec. 1.3Application 使用 This standard can be referenced in specifications for liquid-epoxy coating systems for the interior and exterior of steel water pipelines. The stipulations of this standard apply when this document has been referenced and then only to liquid-epoxy coating systems for the interior and exterior of steel water pipelines. 其他液體環氧內外層涂塑鋼管標準可以參考此標準。制定標準只適用于液體環氧內外層涂塑鋼管。 SECTION 2: REFERENCES 參考 This standard references the following documents. In their latest editions, they form a part of this standard to the extent specified within the standard. In any case of conflict, the requirements of this standard shall prevail.標準參考以下文件。根據以下文件的最新版本，共同組成此標準的內同，如果內容有沖突，以此標準要求為準。 ANSI*/AWWA C203—Coal-Tar Protective Coatings and Linings for SteelWater Pipelines—Enamel and Tape—Hot-Applied. 鋼制供水管道的煤焦油保護涂層和內襯標準.搪瓷和熱纏膠帶 ANSI/AWWA C209—Cold-Applied Tape Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipelines. 鋼水管用特殊部件、連接件和配件的外部用冷纏膠帶層 ANSI/AWWA C214—Tape Coating Systems for the Exterior of Steel Water Pipelines. 鋼管外層纏膠帶 ANSI/AWWA C215—Extruded Polyolefin Coatings for the Exterior of Steel Water Pipelines. 鋼制水管的外層用擠壓聚烯烴涂層 ANSI/AWWA C216—Heat-Shrinkable Cross-Linked Polyolefin Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipelines. 給水鋼管用專用部件、連接件和配件外部可熱收縮交聯的聚烯烴涂層 ANSI/AWWA C217—Cold-Applied Petrolatum Tape and Petroleum Wax Tape Coatings for the Exterior of Special Sections, Connections, and Fittings for Buried or Submerged Steel Water Pipelines. 供水鋼管道專用型鋼、連接件和配件外部冷纏礦脂帶和礦脂臘油帶包覆層 ANSI/AWWA C222—Polyurethane Coatings for the Interior and Exterior of Steel Water Pipelines and Fittings. 鋼水管和配件的內或外的聚氨基甲酸乙酯涂層 ASTM* D3359—Standard Test Methods for Measuring Adhesion by Tape Test. 膠帶試驗用測定粘合性的標準 ASTM D3363—Standard Test Method for Film Hardness by Pencil Test. 鉛筆試驗測定漆膜硬度的標準試驗方法 ASTM D4541—Standard Test