喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有，，圖紙均為高清圖，，CAD圖紙可自行編輯，，有疑問咨詢QQ:1064457796
端罩的沖壓成形工藝及沖壓模具設計
摘要：本設計題目為端罩的設計，體現了深薄壁類零件的設計要求、內容及方向，有一定的設計意義。通過對該零件模具的設計，進一步加強了設計者冷沖模設計的基礎知識，為設計更復雜的冷沖模具做好了鋪墊和吸取了更深刻的經驗。
本設計運用薄板類零件成型工藝及模具設計的基礎知識，首先分析了零件的成分及性能要求，為設計拉深及沖裁模的數據指標做好了準備；然后計算了零件的體積，便于設計落料模的刃口尺寸；最后設計了模具的結構特征，確定了模具的設計參數、設計要點及推出裝置的設計。
沖壓加工分為分離工序和成形工序兩大類。落料、打孔屬于分離工序，拉深屬于成形工序。設計任務是指導老師指定加工的零件為有孔拉深件，材料為鋁L3，厚度為2mm，大批量生產，其他具體要求參照零件圖。根據零件形狀，需要采用落料、拉深、沖孔3個工序，為提高成倍提高生產效率，提高沖壓件的質量，可采用落料和拉深過程集中于一套模具來完成，沖孔工序用簡單模完成。
關鍵詞：落料 拉深 沖孔
The drop-cylinder-shaped pieces of material, drawing, punching, trimming the compound die design
Abstract：The design of the sets of topics for the long injection mold design, reflects the deep thin wall plastic parts of the design, content and direction of a certain design significance. Parts of the mold through the design, the designer has been further strengthened by the injection mold design based on knowledge, for the design of more complex injection molds made and lessons foreshadowing a more profound experience
The use of thin design parts molding process and die design of the basic knowledge, first of all parts of the composition and performance requirements for the design and drawing Die data prepared for the target and then calculate the size of the parts, for design Blanking the edge-size; final design of the structure of the mold, a mold determine the design parameters, design elements and the introduction of the device design.
Cutting and? piercing belong to separating , pulling and stretching belong to calendering. The spare parts fall to cut material-pull and stretch compound die and multiple hole punched die to process.The job is in order to process the multiple hole punched die and pull-stretch die design which is given by the tutor , the material is AL L3 , the thickness is a 2 mm, the large quantity quantity produce, other request to according to the spare parts diagram in a specific way. According to the spare parts’ shape,it need to to cut material,to pull and stretch,to punched hole 3 work, become for the exaltation to raise the production efficiency doubly, raise to? the quantity of part, to cut material and to pull and stretch adopt to compound die to complete, to punched hole adopt to pierce die to complete.
Keywords:cut material ;pull and stretch ; piercing