循跡小車Arduino程序.doc

//循跡小車Arduino 程序： // R是右(right),L是左(left) 小車對著自己看時 分的左右 int MotorRight1=14; //A0 IN1 int MotorRight2=15; //A1 IN2 int MotorLeft1=16; //A2 IN3 int MotorLeft2=17; //A3 IN4 int MotorRPWM=5; //PWM 5 int MotorLPWM=3; //PWM 3 const int SensorLeft = 2; //左感測器輸入腳 const int SensorRight = 6; //右感測器輸入腳 int SL; //左感測器狀態 int SR; //右感測器狀態 void setup() { Serial.begin(9600); pinMode(MotorRight1, OUTPUT); // 腳位 14 (PWM) pinMode(MotorRight2, OUTPUT); // 腳位 15 (PWM) pinMode(MotorLeft1, OUTPUT); // 腳位 16 (PWM) pinMode(MotorLeft2, OUTPUT); // 腳位 17 (PWM) pinMode(MotorLPWM, OUTPUT); // 腳位 3 (PWM) pinMode(MotorRPWM, OUTPUT); // 腳位 5 (PWM) pinMode(SensorLeft, INPUT); //定義左感測器 pinMode(SensorRight, INPUT); //定義右感測器 } void loop() { SL = digitalRead(SensorLeft); SR = digitalRead(SensorRight); if (SL == LOW&&SR==LOW)// 前進 { digitalWrite(MotorRight1,LOW);//IN1 右電機 高電平反轉 digitalWrite(MotorRight2,HIGH);//IN2 右電機 高電平正轉 analogWrite(MotorRPWM,130); //0---100--250 digitalWrite(MotorLeft1,LOW);//IN3 左電機 高電平正轉 digitalWrite(MotorLeft2,HIGH);//IN4 左電機 高電平反轉 analogWrite(MotorLPWM,130); } else // R是右(right),L是左(left) 小車對著自己看時 分的左右 { if (SL == HIGH & SR == LOW)// 左白右黑, 快速左轉 { delay(1); digitalWrite(MotorRight1,HIGH);//IN1 右電機 高電平反轉 digitalWrite(MotorRight2,LOW);//IN2 右電機 高電平正轉 analogWrite(MotorRPWM,130); digitalWrite(MotorLeft1,LOW);//IN3 左電機 高電平正轉 digitalWrite(MotorLeft2,HIGH);//IN4 左電機 高電平反轉 analogWrite(MotorLPWM,130); } else if (SR == HIGH & SL == LOW) // 右白左黑, 快速右轉 { delay(1); digitalWrite(MotorRight1,LOW);//IN1 右電機 高電平反轉 digitalWrite(MotorRight2,HIGH);//IN2 右電機 高電平正轉 analogWrite(MotorRPWM,130); digitalWrite(MotorLeft1,HIGH);//IN3 左電機 高電平正轉 digitalWrite(MotorLeft2,LOW);//IN4 左電機 高電平反轉 analogWrite(MotorLPWM,130); } else // 都是白色, 停止 { digitalWrite(MotorRight1,LOW); digitalWrite(MotorRight2,LOW); analogWrite(MotorRPWM,0); digitalWrite(MotorLeft1,LOW); digitalWrite(MotorLeft2,LOW);; analogWrite(MotorLPWM,0); }}}