【溫馨提示】 dwg后綴的文件為CAD圖，可編輯，無水印，高清圖，，壓縮包內文檔可直接點開預覽，需要原稿請自助充值下載，請見壓縮包內的文件，所見才能所得，下載可得到【資源目錄】下的所有文件哦--有疑問可咨詢QQ:1304139763 或 414951605
摘 要
本論文主要介紹了沖床上下料機械手的設計過程。在查閱了一系列參考資料以后，參閱國內的設計情況。選用圓柱座標和三自由度。機械手的各執行機構，包括:手部、手臂等部。用氣流負壓式吸盤來吸取板料工件。
在分析了具體工作要求，對個方案進行對比之后，綜合考慮各個因素。機械手腰部的旋轉運動需要一定的定位控制精度，故采用步進電機驅動來實現；因?yàn)椴捎靡簤簣?zhí)行缸來做水平手臂和垂直手臂，故大小臂均采用液壓驅動；機械手的手部結構設計，因?yàn)楣ぜ前辶?，使用氣流?fù)壓式吸盤.采用氣動驅動。
關鍵詞：沖床 機械手 負壓吸盤
Abstract
The present paper mainly introduced on the punch press the yummy treats manipulator's design process. After having consulted a series of reference, refers to the domestic design situation. Selects the circular cylindrical coordinate and three degrees-of-freedom. Manipulator's each implementing agency, including: Hand, arm and so on. Absorbs the sheet work piece with the air current negative pressure type sucker. In has analyzed the concrete work requirement, carries on the contrast after a plan, overall evaluation each factor. The manipulator waist's rotary motion needs certain positioning control precision, therefore uses step-by-steps the motor-driven to realize; Because uses the hydraulic pressure execution cylinder to make the horizontal arm and the vertical arm, therefore the big and small arm uses the hydraulic pressure actuation; Manipulator's hand structural design, because the work piece is the sheet, use air current negative pressure type sucker. Uses the air-operated drive.
key words: Punch press manipulator negative pressure sucker
目 錄
摘要..................................................................I
ABSTRACT..............................................................II
緒論 1
1 機械手概述 2
1.1 機械手的組成 2
2 機械手的總體設計 4
2.1.1 機械手總體結構的類型............................................4
2.1.2 設計具體采用方案 5
2.2 機械手腰座結構的設計 6
2.2.1 機械手腰座設計的具體采用方案....................................7
2.3 機械手手臂的結構設計 7
2.3.1 設計具體采用方案 ...............................................8
2.4 機械手的手部結構方案設計 9
2.5 機械手的機械傳動機構的設計 9
2.6 設計具體采用方案 12
2.7機械手驅動系統的設計 12
2.7.1設計具體采用方案................................................19
3 理論分析和設計計算 19
3.1液壓傳動系統設計計算 19
3.1.2擬定液壓執行元件運動控制回路.................................. .21
3.1.3確定液壓系統的主要參數..........................................22
3.1.3.液壓缸主要參數的確定...........................................23
3.1.4計算和選擇液壓元件..............................................25
3.2電機選型和有關計算 27
3.2.1有關參數的計算 27
3.2.2電機型號的選擇 28
3.3吸盤部件的選擇和計算 30
3.3.1真空發生器選定及吸著響應時間計算 32
3.3.2其它氣動元件選定 34
結論 35
參考文獻 36
致謝 ..............................................................37