1922_基于ProToolkit的止動片沖裁模三維參數化設計
1922_基于ProToolkit的止動片沖裁模三維參數化設計,基于,protoolkit,止動片沖裁模,三維,參數,設計
黃河科技學院本 科 畢 業 設 計 任 務 書工 學院 機械 系 機械設計制造與自動化 專業 08 級 1 班學號 080105039 學生 盛菲菲 指 導 教 師 孫 光 華 畢業設計（論文）題目 基于 Pro/Toolkit 的止動片沖裁模三維參數化設計 畢業設計（論文）工作內容與基本要求（目標、任務、途徑、方法，應掌握的原始資料（數據） 、參考資料（文獻）以及設計技術要求、注意事項等） （紙張不夠可加頁）一、工作內容： ? 查閱相關資料，熟悉畢業設計的內容；? ? 完成與課題相關的文獻綜述、文獻翻譯（英譯漢）和開題報告；? ? 沖裁件結構分析、工藝分析及相關計算? ? 沖裁模結構設計、沖裁力及模具工作零件的設計計算；? ? 建立相關的模具標準元件數據庫；? ? 建立模具各元件的三維參數化模型與模具裝配模型；? ? 使用 pro/Toolkit 的 API 函數編程實現模具參數化設計；? ? 模具零件圖與裝配圖繪制；? ? 按照規定的格式要求，撰寫畢業設計說明書一份和軟件使用說明書一份。 二、基本要求 ? 查閱文獻資料不少于 12 篇，其中外文資料不少于 2 篇；文獻綜述不少于 3000 字，外文文獻翻譯不少于 3000 字；? 所設計的模具結構正確合理；? 模具相關元件實現參數化設計；? 所生成的模具零件圖與裝配圖符合國家標準；? 所有畢業設計文檔均需刻入光盤上交；? 畢業設計說明書格式規范。 三、主要參考文獻： [1] 王隆太· 機械 CAD/CAM 技術·北京：機械工業出版社，2005[2] 仲梁維·計算機輔助設計與制造· 北京：北京大學出版社，2006[3] 孫光華·工裝設計.北京：機械工業出版社，2004[4] 單泉等·Pro/E 參數化設計從入門到精通·北京：機械工業出版社， 2008[5] 張繼春· Pro/E 二次開發實用教程·北京：北京大學出版社， 2003[6] （美）Ivor Horton.Visual C++ 2005 入門經典·北京：清華大學出版社，2007四、時間安排：1-4 周 明確設計任務，搜集并熟悉設計相關資料，完成開題報告、文獻翻譯、文獻綜述及總體方案設計，熟悉相關軟件的使用5-6 周 確定模具的結構形式，設計模具各元件，建立相關的模具標準元件數據庫；7-8 周 建立模具各元件的三維參數化模型與模具裝配模型。9-11 周 編程實現模具參數化設計；完成模具零件圖與裝配圖繪制12 周 撰寫與整理畢業設計說明書與軟件使用說明書13 周 修改畢業設計說明書、資格審查等14 周 準備答辯畢業設計（論文）時間： 2012 年 2 月 13 日至 2012 年 5 月 20 日計 劃 答 辯 時 間： 2012 年 5 月 20 日專業（教研室）審批意見：審批人簽名：黃河科技學院畢業設計（論文）開題報告表課題名稱 基于 Pro/Toolkit 的止動片沖裁模三維參數化設計課題來源 教師擬訂 課題類型 CX 指導教師 孫光華學生姓名 盛菲菲 專 業 機械設計制造及其自動化 學 號 080105039一、調研資料的準備根據任務書的要求，在做本課題前，查閱了與課題相關的資料有：機械 CAD/CAM 技術、計算機輔助設計與制造、工裝設計、Pro/E 參數化設計從入門到精通、Pro/E 二次開發實用教程、Visual C++ 2005 入門經典與畢業設計指導等。二、設計的目的與要求 畢業設計是大學教學中最后一個實踐性教學環節，通過該設計過程，可以檢驗學生所學的知識，同時培養學生處理工程中實際問題的能力，因此意義特別重大。所設計的模具結構正確合理；模具相關元件實現參數化設計；所生成的模具零件圖與裝配圖符合國家標準。三、設計的思路與預期成果 1、設計思路首先學習相關軟件的安裝及應用，完成老師布置的練習。然后確定止動片沖裁模的結構形式、定位標準、參數等，并作必要的計算與校核，建立相關的模具標準元件數據庫，建立止動片模具的三維參數化模型及裝配模型。使用 pro/Toolkit 的 API 函數編程實現模具參數化設計，模具零件圖與裝配圖繪制。2、預期的成果（1）完成文獻綜述一篇，不少與 3000 字，與專業相關的英文翻譯一篇，不少于 3000 字（2）完成內容與字?jǐn)?shù)都不少于規定量的畢業設計說明書一份（3）繪制裝配圖，部分零件圖（4）刻錄包含本次設計的所有內容的光盤一張四、任務完成的階段內容及時間安排1-4 周 明確設計任務，搜集并熟悉設計相關資料，完成開題報告、文獻翻譯、文獻綜述及總體方案設計，熟悉相關軟件的使用5-6 周 確定模具的結構形式，設計模具各元件，建立相關的模具標準元件數據庫7-8 周 建立模具各元件的三維參數化模型與模具裝配模型9-11 周 編程實現模具參數化設計；完成模具零件圖與裝配圖繪制12 周 撰寫與整理畢業設計說明書與軟件使用說明書13 周 修改畢業設計說明書、資格審查等14 周 準備答辯五、完成設計（論文）所具備的條件因素本人已修完機械 CAD/CAM 技術、計算機輔助設計與制造、工裝設計、Pro/E 參數化設計從入門到精通、Pro/E 二次開發實用教程、Visual C++ 2005 入門經典與畢業設計指導等課程，借助圖書館的相關文獻資料，以及相關的網絡等資源。指導教師簽名： 日期： 課題來源：（1）教師擬訂；（2）學生建議；（3）企業和社會征集；（4）科研單位提供課題類型：（1）A—工程設計（藝術設計） ；B—技術開發；C—軟件工程；D—理論研究；E—調研報告（2）X—真實課題；Y—模擬課題；Z—虛擬課題 要求（1） 、 （2）均要填，如 AY、BX 等。 黃河科技學院畢業設計 第 1 頁基于Pro/toolkit的止動片沖裁模三維參數化設計摘要：本文介紹了在VC的集成開發環境下開發基于 Pro／toolkit的止動片沖裁模三維參數化設計。提出了利用Pro／E的開發工具Pro／toolkit參數化建模和裝配的方法。并以止動片沖裁模為例詳細介紹了該CAD系統的應用。關鍵詞：Pro／toolkit；止動片沖裁模；參數化設計Abstract: this paper introduces the integrated development environment in VC next based on the development of the Pro/toolkit stop moving piece of punch die 3 dimensional parametric design. Put forward by using Pro/E development tool to Pro/toolkit parameterized modeling and assembly method. And to stop moving piece of punch die for example detailed introduces the application of CAD system. Keywords: Pro/toolkit; Stop moving piece of punch die; Parametric design 前言參數化設計方法具有高效性、實用性的特點，在產品的系列設計、相似設計及專用 CAD 系統開發方面都具有較大的使用價值。與傳統設計方法相比，能夠減少重復勞動，提高設計效率，符合現代產品設計要求。人類文明的發展、科技的進步已和數控機床的研究及Pro／toolkit的三維參數化設計產生了密不可分的關系。實現產品設計的數字化離不開CAD/CAM系統的支持。Pro／E作為通用的三維CAD/CAM系統在功能上基本能滿足產品三維設計要求, 但要高效地進行產品設計以滿足更高層次的要求，必須借助于高級開發工具包Pro／toolkit [1]。Pro／toolkit是PTC 公司為 Pro／E軟件提供的開發工具包，即應用程序接口（API） 。其主要目的是讓用戶或第方通過C程序代碼擴充Pro／ E系統的功能，開發基于Pro／E系統的應用程序模塊，從而滿足用戶的特殊要求。Pro／toolkit工具包提供了開發Pro／E所需的函數庫文件和頭文件， 使用戶能夠定制標準Pro／E用戶界面的能力，自動執行重復性的程序 [2,3]。通過Pro／ E集成的內部程序（DII）或外部應用程序（Exe）可以為造型用戶提供 黃河科技學院畢業設計 第 2 頁自定義的應用程序、設計規劃和繪圖自動化,，并可以實現應用程序模塊與Pro／E系統的無縫集成 [4]。1.止動片沖裁模參數化CAD系統功能簡介利用Pro／toolkit提供的開發接口，主要進行數據庫接口模型、定制的用戶界面模塊和零件參數化模塊的二次開發 [5]。本系統由大模塊構成通過VC++開發的用戶界面模塊、利用Pro／E建立零件模型庫及裝配關系模型庫模塊、實現參數化的Pro ／toolkit應用程序模塊和數據庫模塊。其中各大模塊下又劃分若干個子模塊。各模塊相互關聯，相互調用。這樣便可在Pro／E的環境下顯示止動片沖裁模的三維實體模型。如用戶對當前的設計不滿意, 可返回用戶界面，重新設計，也可在零件模型參數顯示界面更改參數變量重新生成零件。2.Pro／E與 VC接口的實現系統應用 VC 設計應用程序的人機交互界面，利用 Pro／E 的二次開發包Pro／toolkit 提供的函數，編寫 C 語言代碼 [6]。開發基于Pro／E的止動片沖裁模三維參數化CAD系統。系統實現的關鍵是實現Pro ／E與VC系統的無縫連接：（1）在VisualC++集成環境里建立一個基于常規MFC的動態鏈接庫的工程。（2）在工程的CPP文件中編寫 Pro／toolkit入口函數user-initialize() 和終止函數user-terminate()。（3）系統環境定制a.在工程里設置庫文件的環境方法是：Projec→Settings→Link，在Object/Library Modules里添加mpr.lib，protk-dll.lib，prodev-dll.lib，wsock32.lib等庫文件名。b.設置頭文件、庫文件的路徑方法是：Tools→Options→Directories，給出必要的文件路徑。如：D:\PROEWILDFIRE\PROTOOLKIT\INCLUDESD:\PROEWILDFIRE\PROTOOLKIT\I486-NT\OBJ。（4）注冊動態連接文件并運行 黃河科技學院畢業設計 第 3 頁在Pro／E中要運行外部程序，必須對其進行注冊。自動注冊就是把注冊文件放Pro ／E的啟動目錄下即可。而手動注冊就是在Pro／E環境下選取Tools→Auxiliary Application對話框加載該注冊文件。這樣實現的連接后，止動片沖裁模CAD系統就可在Pro／E環境下調用VC的資源，從而可大大擴充原系統的功能，增強了可視化和交互性，提高產品設計質量和效率。3.止動片沖裁模CAD系統參數化建模的實現利用Pro／E的開發包Pro／toolkit提供的函數，在應用程序中通過特征元素樹(featureelementtree)自動創建三維模型的方法比較困難，并且開發包Pro／toolkit沒有提供創建全部特征的相關函數。因此，系統采用以人機交互建立的模型為基礎，通過動態顯示和修改模型的參數變量，來控制模型的結構，達到參數化自動重建的目的 [7]。一般應用在優化技術上，通過將模型參數化，優化過程中不斷對其進行迭代而求出最佳解。參數化建模是參數（變量）而不是數字建立和分析的模型，通過簡單的改變模型中的參數值就能建立和分析新的模型。 參數化建模的參數不僅可以是幾何參數，也可以是溫度、材料等屬性參數。在參數化的幾何造型系統中，設計參數的作用范圍是幾何模型。但幾何模型不能直接用于進行分析計算，需要將其轉化為有限元模型，才能為分析優化程序所用。因此，如果希望以幾何模型中的設計參數作為形狀優化的設計變量，就必須將設計參數的作用范圍延拓至有限元模型，使有限元模型能夠根據設計變量的變化，實現有限元模型的參數化。參數化建模技術在輔助建筑設計上的應用越來越廣泛，其發展時間短暫，發展速度卻令人嘆為觀止，目前在建或已建成的各種形態各異的建筑或多或少都有參數化軟件的設計輔助。3.1在Pro／E 環境下建立止動片沖裁模系統零件庫即在Pro／E環境下建立用于產生一系列衍生件的三維模型樣板。在建立零件模型樣板時，要利用參數(Parameters)模塊創建參數變量，關系式(Relation)模塊建立參數驅動關系, 以保證生成的新模型具有正確的約束和驅動關系 [8]。同時,參數化模型庫的建立也便于零件的統一管理和資源共享。 黃河科技學院畢業設計 第 4 頁3.2參數變量的檢索參數對象(ParameterObject)和參數值(the Valueofaparameter)都是類型為結構體的一種數據對象，參數的檢索、更新都要涉及到這兩個數據結構 [9]。Pro／toolkit函數實現模型參數的檢索，首先必須得到指向該參數對象的指針，若用戶已知參數的名稱，調用ProParameterInit()直接獲取該參數名對應的參數對象指針。若用戶不知道參數的名稱,可調用ProPara-meterVisit()函數遍歷模型中的全部參數 [10]。把檢索模型的參數指針存于類型為參數(ProParameter)的指針數組中。3.3三維模型的參數化重建要實現參數化, 必須實現數據流雙向傳動,即一方面從基準模型設計參數傳遞到交互界面,供用戶修改另一方面,用戶修改后的新參數值要從用戶界面返回到基準模型以實現參數更新,進而重建零件模型 [11]。首先用ProMdlRetrieve()把零件從模型庫調入內存,通過ProParameterlint()或ProParameterVisit()函數檢索出參數對象之后，通過(ProParameter)指針數組中各參數的指針調用ProParameterValueGet()函數可獲得類型為參數值(ProParameterValue)的結構體變量,以此結構體變量為輸入?yún)?shù)調用函數ProParameterValueGet()可設置修改參數之值 [12]。在參數更新之前，須按照約束條件進行參數值合法性檢查。滿足約束條件的新的參數值才能向模型參數值結構體賦值。最后，用ProSolidRegenerate()函數再生三維模型,完成零件的參數化自動重建。這樣,通過函數檢索參數變量并對其賦值,再通過關系式傳遞驅動關系和約束關系,便可控制模型的幾何特征,重建模型。應用該系統設計止動片沖裁模的整體三維裝配圖。4.結論本文利用VC開發環境和Pro／E二次開發技術, 基于特征建模和參數化設計,分析了止動片沖裁模裝配組成及主要零部件之間的聯結關系, 建立了主要零部件和裝配實體模型。確定了止動片沖裁模的主要零件的參數化寸, 建立各尺寸之間的約束關系, 進行止動片沖裁模三維參數化設計和裝配, 實現了設計過程中的自動化和可視化, 大大縮短設計周期、提高設計質量和效率。同時, 系統對其 黃河科技學院畢業設計 第 5 頁它參數化CAD系統的開發有借鑒作用。參考文獻：[1].劉文生，等?；?Pro／E實體模型的參數化二次開發[J].制造業自動化,2005(8):12-14.[2].金淘，陳敏，童水光。Pro／ENGINEER軟件的二次開發技術[J]. 計算機工程及應用,2001(13):148-152.[3].李世國。 Pro／toolkit程序設計[M].北京:機械工業出版社 ,2003.[4].ZANGZ,SARHADIM.An intergration CAD/CAM systerm for automated composite manufacture [J]Journal of Materials Processing Technology,1996,61(1-2）.[5].張繼春· Pro/E 二次開發實用教程 ·北京：北京大學出版社，2003[6].仲梁維· 計算機輔助設計與制造· 北京：北京大學出版社，2006[7]劉潔．三維 CAD 標準件庫的建模與實現方法研究[D]．西安：西安理工大學，2001[8].（美）Ivor Horton.Visual C++ 2005 入門經典·北京：清華大學出版社，2007[9].黃圣杰，張益三，洪立群．Pro／Engineer 2001 高級開發實例[M]．北京：電子工業出版社，2001．[10].張超，張益華． Pro／E 二次開發技術在齒輪三維參數化設計中的應用[J]，2004.[11].單泉等· Pro/E 參數化設計從入門到精通 ·北京：機械工業出版社，2008[12]FFC．Pro ／Toolkit user’s Guide．USA：PTC,2003 畢業設計文獻綜述院 （ 系 ） 名 稱 工 學 院 機 械 系專 業 名 稱 機 械 設 計 制 造 及 其 自 動 化學 生 姓 名 盛 菲 菲指 導 教 師 孫 光 華2012 年 03 月 10 日 Recent achievements in computer aided process planning and numerical modelling of sheet metal forming processesM. Tisza*Manufacturing and processingAbstractPurpose: of this paper: During the recent 10-15 years, Computer Aided Process Planning and Die Design evolved as one of the most important engineering tools in sheet metal forming, particularly in the automotive industry. This emerging role is strongly emphasized by the rapid development of Finite Element Modelling, as well. The purpose of this paper is to give a general overview about the recent achievements in this very important field of sheet metal forming and to introduce some special results in this development activity.Design/methodology/approach: Concerning the CAE activities in sheet metal forming, there are two main approaches: one of them may be regarded as knowledge based process planning, whilst the other as simulation based process planning. The author attempts to integrate these two separate developments in knowledge and simulation based approach by linking commercial CAD and FEM systems.Findings: Applying the above approach a more powerful and efficient process planning and die design solution can be achieved radically reducing the time and cost of product development cycle and improving product quality.Research limitations/implications: Due to the different modelling approaches in CAD and FEM systems, the biggest challenge is to enhance the robustness of data exchange capabilities between various systems to provide an even more streamlined information flow.Practical implications: The proposed integrated solutions have great practical importance to improve the global competitiveness of sheet metal forming in the very important segment of industry.Originality/value: The concept described in this paper may have specific value both for process planning and die design engineers.Keywords: Analysis and modelling; Knowledge and simulation based systems1. Introduction In the recent years, the role and importance of metal forming processes in manufacturing industry have been continuously increasing primarily due to its material- and cost-effective nature. It is further emphasised by the recent advances in tools, materials and design, which in turn provide significant improvements in the mechanical properties and tolerances of the products. It is also characteristic for metal forming processes that the final shape of the component cannot be produced generally by a single operation, but more often several operations should be performed to transform the initial simple geometry into a more complex product. Moreover, in the recent years metal forming develops in the direction of net-shape or near-net-shape manufacturing to reduce the need for subsequent machining operations and to minimise the total manufacturing represent very important and complex tasks. The global competition also requires that manufacturing industry – besides the skill and the experience accumulated in the shop practice – should increasingly utilise proven techniques of Computer Aided Engineering for rapid and cost effective process design and tool manufacturing. The application of various methods of Computer Aided Engineering has become one of the most important topics in manufacturing industries and particularly in the automotive industry. The application of various CAE techniques practically covers the full product development cycle from the conceptual product design through the process planning and die design up to the manufacturing phase of the production. CAE techniques are widely used in sheet metal forming, for example to predict the formability, to determine the type and sequences of manufacturing processes and their parameters, to design forming tools, etc. The importance of the application of CAE tools becoming more and more important as the manufactured parts are becoming ever increasingly complex. As the need for the widespread application of CAE techniques driven by the demand of global competitiveness accelerates, the need for a robust and streamlined Process and Die Design Engineering (PDDE) becomes more and more crucial. Recently, there are two main approaches to achieve these goals. One of them is the application of knowledge-based expert systems, which are generally based on simplified plasticity theory and empirical technological rules. There are a great number of papers dealing with the exclusive use of knowledge-based systems both in sheet and bulk metal forming [1-3]. However, the exclusively knowledge based solutions have certain disadvantages: they usually cannot provide an enough accurate solution to the problem since these systems are generally based on simple technological rules with limited validity. Therefore knowledge-based systems cannot predict for example the material flow, and usually cannot provide the accurate stress and strain distribution inside the component. As another approach, numerical techniques (recently mainly finite element modelling) are applied for the analysis of the plastic deformation [4-6]. The main objectives of the application of numerical process simulation in metal forming are to determine appropriate process parameters and to develop adequate die design by process simulation, to improve part quality by predicting process limits and preventing flow induced defects. Besides these, numerical process simulation also leads to reducing process and die try-out, as well as shorter lead times, while significantly reducing manufacturing costs. But the exclusive use of numerical modelling – like it is the case in the exclusive use of knowledge-based systems – has also some drawbacks, too. In spite of the enormous development of hardware and software facilities, the reliability of results is often dependent on the experiences of the user. It is partly due to the large number of operating parameters whose influence should be investigated, and partly due to the numerical difficulties caused by the complexity of the applied mathematical model to describe the material behaviour. Therefore, in the recent years the integration of these two fields (i.e. the knowledge-based systems and numerical modelling) has gained primary importance [7]. 2. Process planning and die-design in sheet metal One of the main drawbacks in industrial practice hindering the even more wide application of simulation techniques that the output results of simulation packages are not usually directly and easily usable for computer aided die design. Obviously, there are tremendous efforts to successfully link CAD and FEM systems, however, still there are a lot to do in this field [8]. This solution requires a fully integrated approach of computer aided product design, process planning and die design, as well as the finite element simulation of the forming processes. It means that simulation tools should be efficiently used throughout the whole product development cycle [9]. This concept will be illustrated through the examples of automotive part production. In our practice, we use Unigraphics NX 4 as a commercial CAD system for supporting the Computer Aided Process Planning and Die Design tasks and the AutoForm 4.05 and PAM-STAMP 2G are used as the numerical simulation tools, however, the principles applied here can be similarly adopted by using different CAD and simulation packages, too. Before analysing this integrated solution, let’s summarize the main features of forming process planning and die design in so-called conventional CAD environment .2.1Process planning and die-design in conventional CAD environmentStamping industry applies CAD techniques both in the process planning and die design already for many years. However, in a ?traditional” CAD environment, these are practically stand-alone solutions, i.e. for example a knowledge based process planning solution is applied for the determination of the necessary types of forming processes, even in some cases, the forming sequences can be determined in this way together with the appropriate process paramteres, too. After determining the process sequences and process parameters, the forming dies are designed using sophisticated CAD systems, however, still we do not have any evidence whether the designed tools will provide the components with the prescribed properties. Therefore, before it goes to the production line, usually a time- and cost consuming try-out phase follows, as it is shown in Fig.1 If the try-out is successful, i.e. the die produces parts with no stamping defects, it will be sent to the stamping plant for production. On the other hand, if splitting or wrinkling occur during the tryout, the die set needs to be reworked. It means that we have to return first to rework the die construction by changing the critical die parameters (e.g. die radii, drawing gap, etc.). If it does not solve the problem, a new die design, or a new process planning is required. Some cases, we have to go back even to the product design stage to modify the product parameters. The more we go back the higher the development and design costs are. Occasionally, the die set is scraped and a perfectly new product-, process- and die design is needed. As a result, die manufacturing time is increased as well as the cost of die making. 3. Process planning and die-design in sheet metalSimulation and Knowledge Based Systems – An Integrated ApproachAs it was mentioned before, this solution will be described through the example of an automotive sheet metal component using the Unigraphics NX (version 4.0) as the CAD system, and the AutoForm 4.05 as the FEM package, however, the principles applied here, can be adopted to other programs as well [10]. The selection of these two program packages can be explained by several reasons. On the one hand, both the Unigraphics and the AutoForm are among the most widely applied packages in the automotive industry in the World. On the other hand, these two systems are among the first to offer a special interface module to enhance the information and data exchange between CAD modelling and FEM simulations in both directions making possible the most efficient integration during the whole product development cycle. In the forthcoming sections, this solution will be described in detail following the road map of this simulation-guided process planning and die design procedure. 3.1.Geometric modelling of the sheet metal componentThe CAD model of the component created by the product design engineer is shown in Fig.3. As it often happens in the automotive industry, the component has a symmetric counterpart (so-called left and right handed or double attached parts). The part model is created in Unigrapics NX 4.0 CAD system as a solid model. However, FEM systems dedicated for sheet metal forming usually require surface models. Therefore, before exporting the part model a surface model should be created. This function is well-supported in most CAD systems. Depending on the simulation requirements, even we can decide which surface (top, middle or bottom) will be exported into the surface model. 3.2.Feasibility of the component formabilityIn most cases, process planning engineers would like to know right at the beginning whether the component can be manufactured with the planned formability operations. Therefore, after importing the surface model of the component with the AutoForm input generator, first a fast feasibility study should be performed. The AutoForm has an extremely well suited module for this purpose: in the so-called One-Step simulation module, this formability analysis can be done even if we do not have any or just very few information on the forming tools. Using this One-Step simulation procedure, a quick decision can be made if any modification of the part is required. Besides the part formability validation in this very early stage of product development, further important possibilities are also offered in this module including the analysis of slight part modifications, studying alternative material types and grade, or various thicknesses, material cost estimation and optimization, etc. If this feasibility study is successful as shown for example for this component in Fig.4, the work of process planning engineer can be efficiently supported by determining the optimum blank shape and sizes. 4. ConclusionsComputer aided engineering has a vital and central role in the recent developments in sheet metal forming concerning the whole product development cycle. The application of various methods and techniques of CAE activities resulted in significant developments: the formerly trial-and-error based workshop practice has been continuously transformed into a science-based and technology driven engineering solution. In this paper, an integrated approach for the application of knowledge based systems and finite element simulation is introduced. Applying this knowledge and simulation based concept for the whole product development cycle – from the conceptual design through the process planning and die design as an integrated CAE tool – provides significant advantages both in the design and in the manufacturing phase. Sheet metal forming simulation results today are already reliable and accurate enough that even tryout tools and the time consuming tryout processes may be eliminated or at least significantly reduced. Thus, the integrated solution described in this paper results in significantly shorter lead times, better product quality and as a consequence more cost-effective design and production.AcknowledgementsThis research work was jointly financed by the Hungarian Academy of Sciences (MTA) and the National Science Foundation (Ref. No.: OTKA NI 61724). This financial support is gratefully acknowledged. References[1] S.K. Sitaraman, T. Altan, A Knowledge Based System for Process Sequence Design in Sheet Metal Forming, Journal of Materials Processing and Technology (1991) 247-271. [2] N. Alberti, L. Cannizaro, F. Micari, Knowledge Based Systems and FE Simulations in Metal Forming Processes, Annals of CIRP 40 (1991) 295-298. [3] L. Eshelby, M. Barash, W. Johnson, A Rule Based Modelling for Planning Axisymmetric Deep-drawing, Journal of Mechanics Sciences (1988) 1-113. [4] A. Makinouchi, Sheet Metal Forming Simulation, Journal of Materials Processing and Technology 60 (1996) 19-26. [5] A.E. Tekkaya, State of the art of Simulation in Sheet Metal Forming, Journal of Materials Processing and Technology 103 (2000) 14-22. [6] T. Altan et al., Simulation of Metal Forming Processes, Proceedings of the 6th International Conference ICTP, Nuremberg, 1999, 23. [7] M. Tisza, Numerical Modelling and Knowledge Based Systems in Metal Forming, Advanced Technology of Plasticity 1 (1999) 145-154. [8] A. Andersson, Information Exchange within Tool Design and Sheet Metal Forming, Journal of Engineering Design 12 (2001) 283-291. [9] A. Andersson, Comparison of Sheet Metal Forming Simulation and Try-out Tools in Design of Forming Tools, Journal of Engineering Design15 (2004) 551-561. [10] M. Tisza, Numerical Modelling and Simulation: Academic and Industrial Perspectives, Materials Science Forum 473-474 (2005) 407-414. 近年來計算機輔助工藝規劃和板料成形數值模擬過程米蒂薩河*制造和加工摘要目的：本文：在最近的10 - 15年，計算機輔助工藝設計及模具設計的進化成為其中一個最重要的工程工具板料成形過程中，特別是在汽車工業。這一新興的角色是強烈的迅速發展，強調了有限元模型。本文的目的是給出一個概述，關于近年來所取得的成就在非常重要的板料成形領域，介紹一些在這個發展活動中的特殊結果。設計/方法/途徑:對板料成形 CAE 活動，主要有兩種方法：其中一個可能被看作是基于知識的工藝設計，而另一個基礎工藝規劃為仿真。作者試圖通過商業CAD 系統和有限元方法整合這兩個獨立發展的基礎知識和仿真方法。結果：應用上述方法一個更強大、更高效的工藝設計及模具設計的解決方案可能達到徹底降低芯片制造時間和費用，降低產品開發周期，提高產品質量的效果。研究局限性/含義：由于有限元方法和 CAD 系統不同的造型方法 ,最大的挑戰是提高數據交換能力較強的魯棒性之間的不同系統以提供一個更精簡的信息流動。實際應用：該綜合解決方案對于提高板料成形過程中很重要的工業環節的全球競爭力有重要的現實意義。創意/價值：本文中介紹的概念對于工藝設計及模具設計工程師都可能有特定價值。關鍵詞：分析和模型；基于知識和仿真系統。1.介紹近年來成型過程的作用與重要性在制造業中不斷增加，主要由于其材料和精打細算的性質。這是進一步強調了近年來的工具、材料和設計，從而提供顯著的改善力學性能及公差的產品。它也是對金屬板料成形特點中最后形成的組件不能由一般生產的一次手術，但是更常見的幾種手術應把初始簡單的幾何變換成一個更復雜的產品。此外，近年來在金屬成形的方向發展分析鈑制帶輪近凈減少或制備生產需要后續加工操作，并盡量避免妨礙總生產成本。因此，金屬成形工藝設計和工具設計代表了一個非常重要且復雜的任務。全球競爭也需要制造業，除了在商店實踐的技能和經驗積累，也應該越來越利用電腦輔助工程實踐技術的快速和低成本的工藝設計和工具制造。應用多種多樣的計算機輔助工程已成為最重要的課題之一，特別是在制造業的汽車工業。各行各業的 CAE 技術應用幾乎涵蓋了從產品概念設計到工藝設計及模具設計到制造階段的生產的全部產品開發周期。CAE 技術廣泛應用于板料成形，預測，確定型號序列參數和生產流程，設計成形模具，等。應用 CAE 技術對于制造日益復雜的工具零件的重要性越來越大。因?yàn)樾枰?CAE 技術的廣泛應用來加速推動全球競爭力，需要一個良好的魯棒性和流線型的過程和模具設計工程(PDDE)變得越來越重要。最近，有兩個主要的方法來實現這些目標。其中一個是基于知識的專家系統的應用，這通常是基于簡化塑性理論和實證技術規則。將會有非常大量的文件處理知識系統專用權都和大量的金屬成形板材[1 - 3]。然而，專門為以知識為基礎的解決方案有一定的缺點：他們通常無法提供足夠精確的解決這個問題的方法，因?yàn)檫@些系統通?；诤唵蔚募夹g(shù)規則和限制的有效性。因此知識系統無法預測例如物流，而且通常不能提供準確的應力和應變分布在組件。作為另一個方法，數值方法(主要是有限元模型)被廣泛應用于分析塑性變形[4 - 6]。應用的主要目的數值模擬在金屬成形過程中，確定合適的工藝參數和提供足夠的模具設計過程仿真，提高產品的質量，防止被預測的工藝范圍流激缺陷。除了這些，也會通過數值過程模擬減少工藝、模具選拔以及交貨周期，同時大大降低制造成本。但獨家使用數值模擬的研究 ——就象它是這個案子獨家使用知識系統，也有一些弊端，也具有一定的參考價值。盡管硬件和軟件設施快速發展，其可靠性結果也往往取決于用戶的經驗。其中一部分是由于大量的操作參數的影響需進行調查,另一部分是由于應用數學模型描述材料的行為造成數值困難的復雜性。因此,在近年來的整合這兩個領域（如知識系統和數值模擬）的研究已獲得了重要進展[7]。2.工藝設計和 die-design 金屬片一個主要的缺點在工業實踐阻礙更廣泛應用仿真技術，輸出結果的模擬軟件包通常不直接和容易使用計算機輔助模具設計。顯然，還要有巨大的努力去成功連接計算機輔助設計和有限元系統，但是，在這一領域仍然有很多事情需要做[ 8]。這就需要一個完全集成的方法計算機輔助產品設計，工藝設計和模具設計，以及有限元模擬形成過程。這意味著仿真工具應該被有效的利用整個產品開發周期[9]。這一概念將通過實例的汽車零件生產。在實踐中，我們使用 Unigraphics NX 的4作為商業 CAD 系統支持計算機輔助工藝設計及模具設計的任務、AutoForm 4.05和 PAM-STAMP 2 G 作為數值模擬工具，然而，采用的原則在這里同樣可以通過使用不同的計算機輔助設計與仿真軟件包。在分析這種綜合的解決方案,讓我們總結形成過程規劃的主要特點及模具設計在所謂的傳統 CAD 環境。2.1.傳統 CAD 環境中的工藝設計及模具設計沖壓行業應用計算機輔助設計技術在工藝設計和模具設計已經很多年了。然而，在傳統的環境，這些幾乎是獨立的解決方案，即例如基于知識的工藝規劃的解決方案是用于確定必要的類型的形成過程中，甚至在某些情況下，形成序列也可以用這種方法連同適當?shù)倪^程 paramteres。在確定過程中的序列和工藝參數，成形模具的設計采用了先進的計算機輔助設計系統，然而，我們?nèi)匀粵]有任何證據是否設計的工具將提供部分規定的特性。因此，在它的生產線，通常是一個時間和成本消耗，試行階段如下，顯示圖1。如果試驗是成功的，即模具生產零件沒有沖壓缺陷，它將被發送到?jīng)_壓廠生產。另一方面，如果分裂或起皺發生在試模，模具需要重做。這意味著我們必須返回第一返工的模具結構改變的關鍵參數（如模具模具半徑，模具間隙，等。 ） 。如果不解決這個問題，一個新的模具設計，或一個新的工藝規劃是必要的。某些情況下，我們必須返回到產品設計階段的產品參數修改。我們越回較高的開發設計成本。偶爾，模具刮和一個完美的新產品，工藝和模具的設計是必要的。因此，模具制造時間增加以及成本的模具制作。3.仿真和基于知識的系統–綜合方法就像前面提到的，該方案將通過一個例子：汽車鈑金部件使用 UG（4版）為計算機輔助設計系統，AutoForm 4.05為有限元分析軟件包,然而,這個原則應用在這里,也可以用于其他方案[10]。這兩個項目的選擇軟件包可以解釋為幾個原因。一方面，這兩個 UG 和AutoForm 是最廣泛應用的軟件包在世界汽車工業。另一方面，這兩個系統是最早提出一項特殊的接口模塊，提高信息和數據交換之間的建模和數值模擬兩個方向可能是最有效的整合在整個產品開發周期。在即將到來的部分，這個方案將被用來詳細描述 simulation-guided 地圖的工藝設計及模具設計過程。3.1.金屬板材的幾何造型的組成部分先進的 CAD 模型的組成由產品設計工程師被顯示在圖。因?yàn)樗０l(fā)生在汽車行業、組件都有一個對稱的對手(所謂的左、右撇子或雙附件)。部分模型 Unigrapics NX 創造4.0 CAD 系統作為一個實體模型。然而，專用有限元板料成形系統通常需要表面模型。因此，在出口前部分模型表面模型應該被創造出來。這個函數是良好的支持在大多數 CAD 系統。根據仿真需求，即使我們可以決定哪些表面(上層、中層或底部)將被出口到曲面模型。3.2.部分成型的可行性在大多數情況下，工藝設計工程師想知道部件可以開始生產的成形性與計劃行動是否正確。因此，在引進曲面模型的輸入組件 AutoForm 發電機，首先應進行快速的可行性研究。這 AutoForm 有極適合模塊為這個目的：在所謂的一步法仿真模塊，該成形性能做了分析，即使我們沒有任何信息或者只是很少的形成的工具。使用這個一步仿真程序，一個快速的決定，可以做任何修改的部分是必需的。除了部分成形性能驗證在這個早期階段的產品開發，更重要的可能性也提供在本模塊包括分析細微部分修改，研究替代材料的類型和等級，或不同的厚度，材料成本的估算和優化，等。如果這個可行性研究是成功的，如圖所示，例如該組件圖工藝規劃工程師的工作，可以有效地支持確定最佳毛坯形狀和尺寸。4.結論在金屬板料成形的整個產品開發周期中計算機輔助工程具有重要的核心作用并且扮演著重要的角色。應用 CAE 各種方法和技術的活動產生重大進展：以原試車間實踐為基礎一直不斷轉化為科學和技術驅動的工程解決方案。本文提出了一個綜合的方法的應用，以知識為基礎的系統和有限元模擬方法。應用這些知識和仿真的基礎概念，為整個產品開發的周期，從概念設計到工藝設計及模具設計為一體的 CAE 工具，具有明顯的優勢，無論在設計和制造階段。今天的金屬板料成形模擬結果已經足夠精確可靠，甚至調試工具和耗時的調試過程可能被取消或至少顯著降低。因此，本文描述的綜合解決結果顯著地縮短交貨期，提高了產品質量，因而更具成本效益的設計與生產。鳴謝這項研究工作是由匈牙利科學研究院（中國）和美家科學基金會（參考編號：otka 鎳61724）共同出資。對這種財政支持表示感謝。參考文獻[1] S.K. Sitaraman, T. Altan，一個基于知識的系統的工藝流程設計在板材成型過程中，材料加工技術雜志（1991）247-271。[2] N. Alberti, L. Cannizaro, F. Micari，基于知識的系統和有限元模擬金屬成形過程中，志40（1991）295-298。[3] L. Eshelby, M. Barash, W. Johnson，一個以規則為基礎的模擬規劃軸對稱拉深，力學學報科學（1988）1-113。[4] A. Makinouchi，板料成形模擬，材料加工技術雜志，60（1996）19 - 26。[5] A.E. Tekkaya，國家藝術的仿真技術在板料成形，材料加工技術雜志，103（2000）14 - 22。[6] T. Altan et al.，模擬金屬成型過程，第六屆國際會議國際理論物理中心，紐倫堡，1999，23。[7] M. Tisza，數值模擬，基于知識的系統在金屬成形，工藝先進的可塑性，1（1999）145-154。[8] A. Andersson，信息交換的工具設計和鈑金成形，工程設計學報12（2001）283-291。[9] A. Andersson，比較鈑金成形模擬及試驗工具成型刀具的設計，工程雜志（2004）551-561design15 。[10] M. Tisza，數值模擬與仿真：學術和工業的角度來看，材料科學論壇 473-474（2005）407-414。
收藏