拉中拉深壁

1、拉中拉深壁起皺的分深模設計析 F K C 灣大學機械設計研究所 在帶有斜度的方形盒和帶有階梯的方形盒的拉深中發生的起皺現象一直在被研究。這兩中類型的起皺現象有一個共同的特征：全都發生在相對無支撐、無壓邊的拉深壁處。在帶有斜度的方形盒的拉深中，常受到工序參數的影響，例如：模具的間隙值和壓邊力等，所以常用有限元模擬的方法來研究分析起皺的發生。模擬的結果表明模具的間隙值越大，起皺現象就越 嚴重，而且增加壓邊力也不能抑制和消除起皺現象的發生。在帶有階梯的方形盒拉深的起皺現象分析中，常通過實際生產中一種近似的幾何。

2、 2002) 19:253259 2002 in a in of is A of of is at is In of a as on of is is be by In of in a an a of at to of An of is in of of is of in in a of in of to In of a 14, 0617. in in is by is of It is of in be in by of to by a to on on of to in of a a a of to of et 1 a in a of an in of is to in Yu et 2,3 to 4of it to to on of a In 990s, D to it to in In D to of on at in of a of a as 1(a), an on of to is is 1. a) a b) a to In of on In of a as 1(b),of is In to of an in of an to by on an AD to A。

3、拉中拉深壁起皺的分深模設計析 F K C 灣大學機械設計研究所 在帶有斜度的方形盒和帶有階梯的方形盒的拉深中發生的起皺現象一直在被研究。這兩中類型的起皺現象有一個共同的特征：全都發生在相對無支撐、無壓邊的拉深壁處。在帶有斜度的方形盒的拉深中，常受到工序參數的影響，例如：模具的間隙值和壓邊力等，所以常用有限元模擬的方法來研究分析起皺的發生。模擬的結果表明模具的間隙值越大，起皺現象就越 嚴重，而且增加壓邊力也不能抑制和消除起皺現象的發生。在帶有階梯的方形盒拉深的起皺現象分析中，常通過實際生產中一種近似的幾何。

4、 2002) 19:253259 2002 in a in of is A of of is at is In of a as on of is is be by In of in a an a of at to of An of is in of of is of in in a of in of to In of a 14, 0617. in in is by is of It is of in be in by of to by a to on on of to in of a a a of to of et 1 a in a of an in of is to in Yu et 2,3 to 4of it to to on of a In 990s, D to it to in In D to of on at in of a of a as 1(a), an on of to is is 1. a) a b) a to In of on In of a as 1(b),of is In to of an in of an to by on an AD to A。