無柄塑料水杯注塑塑料模具設計（含CAD圖紙、說明書）

水杯模具設計 機電工程學院模具設計與制造專業 阮靖皓 摘要：嵌件成型（Insert Molding）指在模具內裝入預先準備的異材質嵌件后注入樹脂，熔融的材料與嵌件接合固化，制成一體化產品的成型工法。為了增加塑料制品整體或某一部位的強度與剛度，滿足使用的要求，常在塑件體內設置金屬嵌件。 隨著產品的功能的日益提高，嵌件模的應用也越來越廣泛，目前已廣泛應用于汽車零配件，家用電器，電腦，手機，連接器等的模具里。嵌件模有它的獨有的特點，設計嵌件模時，塑膠件要放縮水，而嵌件一般是不放縮水的，這就涉及到塑件和嵌件的位置尺寸的處理問題。由于嵌件的種類繁多，形狀大小不一，嵌件的安裝和定位，也是這類模具設計的另一難點。 關鍵詞：水杯 模具結構  目錄 水杯模具設計 1 引言 3 1 塑件工藝性分析 3 1.1 塑件的原材料分析 3 (1) 塑件材料性能分析 3 (2) 成型工藝性分析 5 1.2 塑件結構分析 5 2 擬定模具結構形式 6 2.1 分型面位置確定 6 2.2 型腔數量及排列方式確定 7 2.3 注塑機選擇和參數校核 7 2.3.1 注射量計算 7 2.3.2 投影面積及鎖模力的計算 8 2.3.3 選擇注射機 8 根據注射機的注射容量需大于46.2cm3、鎖模力需大于366.24kN， 9 2.3.4 注射機有關參數的校核 9 3 成型零件有關尺寸的計算 10 1）型腔徑向尺寸按以下公式計算 11 2）型腔深度尺寸按以下公式計算 11 4 澆注系統的設計 14 4.1 澆口套的選用 14 4.2分流道的設計 15 （1）分流道截面形狀 15 （2）分流道的尺寸 15 4.3分流道的布置 16 4.4澆口設計 17 4.5澆口位置的選擇 18 5 合模導向機構以及定位裝置的設計 19 5.1導向機構的設計 19 5.2定位裝置的設計 20 6 脫模結構的設計 20 7 排氣系統的設計 22 8 繪制模具裝配圖以及模具的安裝試模 22 裝配的繪制 22 結論 25 謝辭 25 引言 近年來，中國塑料模具制造水平已有較大提高。目前，塑料模具在整個模具行業中所占比重約為30%，在模具進出口中的比重高達50～70%。目前，帶嵌件模具發展也是相當?shù)目臁，F(xiàn)在最常見帶嵌件模具是帶金屬嵌件的模具以及帶樹脂嵌件的模具。結合Pro/E、Moldex3D等CAE分析軟件一起對帶嵌件模具進行模擬分析，從而來指導帶嵌件模具設計及其工藝方案的優化，已經成為了當今社會的一個的重要研究手段。但是總體說來，對帶嵌件的模具設計仍然還不成熟。 塑料產品從設計到成型生產是一個十分復雜的過程，它包括塑料制品設計、模具結構設計、模具加工制造和模塑生產等幾個主要方面，它需要產品設計師、模具設計師、模具加工工藝師及熟練操作工人協同努力來完成，它是一個設計、修改、再設計的反復迭代，不斷優化的過程。傳統的手工設計已越來越難以滿足市場激烈競爭的需要。計算機技術的運用，正在各方面取代傳統的手工設計方式，并取得了顯著的經濟效益。 1 塑件工藝性分析 1.1 塑件的原材料分析 產品名稱: 水杯 型腔數:一模四腔 生產類型:大批量 材料: PP 圖 1-1 (1) 塑件材料性能分析 PP塑料，化學名稱：聚丙烯 ?? 英文名稱:Polypropylene（簡稱PP） 　 比重:0.9-0.91克/立方厘米 成型收縮率:1.0-2.5% 成型溫度：160-220℃ 。 成分結構 　　PP為結晶型高聚物，常用塑料中PP最輕，密度僅為0.91g/cm3（比水?。?。通用塑料中，PP的耐熱性最好，其熱變形溫度為80-100℃，能在沸水中煮。PP有良好的耐應力開裂性，有很高的彎曲疲勞壽命，俗稱“百折膠”。PP的綜合性能優于PE料。PP產品質輕、韌性好、耐化學性好。PP的缺點：尺寸精度低、剛性不足、耐候性差，它具有后收縮現象，脫模后，易老化、變脆、易變形。 成型特性 　　1)結晶料,吸濕性小,易發生融體破裂,長期與熱金屬接觸易分解。 　　2)流動性好,但收縮范圍及收縮值大,易發生縮孔.凹痕,變形。 　　3)冷卻速度快,澆注系統及冷卻系統應緩慢散熱,并注意控制成型溫度。料溫低溫高壓時容易取向,模具溫度低于50度時,塑件不光滑,易產生熔接不良,流痕,90度以上易發生翹曲變形 　　4)塑料壁厚須均勻,避免缺膠,尖角,以防應力集中。 PP與其它幾種主要的通用塑料的性能比較 　　 表1-1 材料性能表 材料性能、種類 PP PE PVC PS ABS 密度 最小 小于水 較大 略高于水 略高于水 剛性　 較好 差 好 好 好 收縮率 差 一般 好 好 好 韌性 低溫下差 好 差 差 好 強度 較高 低 較高 高 高 耐熱性 好 一般 差 較差 較差 化學穩定性 好 好 好 好 好 耐候性 差 差 一般 一般 較差 毒性 無毒 無毒 可以無毒 無毒 無毒 粘合劑粘合 差 差 好 一般 一般 熱合性 一般 好 一般 一般 一般 成型加工性 好 好 不易 好 好 (2) 成型工藝性分析 　　PP在熔融溫度下有較好的流動性，成型性能好，PP在加工上有兩個特點：其一：PP熔體的粘度隨剪切速度的提高而有明顯的下降（受溫度影響較?。?；其二：分子取向程度高而呈現較大的收縮率。 　　PP的加工溫度在200-300℃左右較好，它有良好的熱穩定性（分解溫度為310℃），但高溫下（270-300℃），長時間停留在炮筒中會有降解的可能。因PP的粘度隨著剪切速度的提高有明顯的降低，所以提高注射壓力和注射速度會提高其流動性，改善收縮變形和凹陷。模溫宜控制在30-50℃范圍內。PP熔體能穿越很窄的模具縫隙而出現披鋒。PP在熔化過程中，要吸收大量的熔解熱（比熱較大），產品出模后比較燙。PP料加工時不需干燥，PP的收縮率和結晶度比PE低。 1.2 塑件結構分析 塑件的具體結構如圖所示。其中塑件外形結構大致圓柱形，帶有拔模角度，注塑重點在于，注塑時不能出現澆不足，收縮均勻。同時外觀要求不能有熔接痕、脫模痕, 不能有劃傷、變形、飛邊，必須符合GB/T 2828.1、QC/T 32-2006和GB/T 3730.1-2001。 制品尺寸精度分析。該塑件尺寸無特殊要求，尺寸精度按MT5查取公差。該塑件內外尺寸均受到模具活動的影響，故為B類尺寸。據國家標準塑件尺寸公差（GB/T144486-1993）查得，該零件主要尺寸如下所示： 表1-2 塑件標注尺寸 尺寸公差（MT5） 塑件標注尺寸 尺寸公差（MT5） 尺寸 18 18±0.3 尺寸 1 1±0.3 20 20±0.3 32 32±0.3 23 23±0.3 33 33±0.3 25 25±0.3 27 27±0.3 圖1-2 水杯三維圖 2 擬定模具結構形式 2.1 分型面位置確定 在模具設計初期階段，應首先確定分型面的位置，然后才選擇模具的結構。分型面設計是否合理，對塑件質量、工藝操作難易程度和模具的設計制造都有很大影響。因此，分型面的選擇是在注射模設計中的一個關鍵因素。 分型面的選擇主要應遵循以下原則： （1) 分型面應選在塑件外形最大截面處。 （2) 便于塑件順利脫模，盡可能使塑件留在動模一側。 （3) 有利于保證塑件的精度要求。 （4) 滿足塑件的外觀質量要求。 （5) 有利于簡化模具結構。 （6) 盡量減少塑件在合模方向上的投影面積。 （7) 有利于排氣。 綜合上述的各原則，分型面可取在制件的最大投影面積處。 圖 2-1 分型面 2.2 型腔數量及排列方式確定 該塑件三維是?54上×?40下×66高mm，為中小型尺寸工件，采用一模四腔，大批量生產。排列如圖所示。 圖 2-2 型腔排列 2.3 注塑機選擇和參數校核 2.3.1 注射量計算 模具所需塑料熔體注射量m = nm1 + m2 (3-1) 式中： m— 一副模具所需塑料的質量或體積（g或cm3）; n — 初步選定的型腔數量； m1— 單個塑件的質量或體積（g或cm3） m2— 澆注系統的質量或體積（g或cm3） 其中m2是個未知值（注塑廠的統計資料），在做設計時以0.6nm1來估算，即 m = 1.6n m1 (3-2) 經proe分析，塑件質量m1= 5.9480.91=5.412g，所以注射量m=1.6nm1=1.645.4=34.56g 2.3.2 投影面積及鎖模力的計算 塑件和流道凝料（包括澆口）在分型面上的投影面積及所需鎖模力為： A = nA1+A2 (3-3) Fm=(nA1+A2)P型 (3-4) 式中： A —塑件及流道凝料在分型面上的投影面積（mm2）; A1—單個塑件在分型面上的投影面積（mm2）； A2—流道凝料（包括澆口）在分型面上的投影面積（mm2）; Fm —模具所需的鎖模力（N）； P型—塑料熔體對型腔的平均壓力（MPa）。 表5-1 常用塑料注射成型時型腔平均壓力 單位：MPa 塑件特點 P型 舉例 容易成型塑件 25 PE、PP、PS等壁厚均勻的日用品， 一般塑件 30 容器類 中等黏度塑件及有精度要求塑件 35 在模溫較高的情況下，成型薄壁容器類 高黏度塑料及高精度、難充模塑料 40 ABS、POM等有精度要求的零件，如殼類等高精度的機械零件，如齒輪、凸輪等 流道凝料(包括澆口)在分型面上的投影面積A2，在模具設計前是個未知值，根據多型腔模的統計分析，A2是每個塑件在分型面上的投影面積的0.2倍到0.5倍，因此可用0.45nA1來估算，另外部分塑料注射壓力P可查相關數據。經過moldex 3D 的計算，總投影面積為：9156mm2。 所以：A=4（3.14*27*27）=9156mm2 Fm =AP型=9156×40=366.24kN 2.3.3 選擇注射機 根據上面計算得到的m和Fm值來選擇一種注射機，注射機的最大注射量（額定注射量G）和額定鎖模力F滿足 G≥ m/α (3-5) 式中α—注射系數，無定型塑料取0.85，結晶型塑料取0.75。 F>Fm (3-6) 則：G≥m/α→G≥34.56g/0.85=40.66g 生產原料密度為1.76g/cm3 注射容量為23.1 cm3 一般注塑機澆注塑料原料時, 其每次注射量僅達標準注射量的75 %。為了提高制件質量及尺寸穩定, 表面光澤、色調的均勻, 要求注射量為標定注射量的50 %為宜，即46.2cm3。 根據注射機的注射容量需大于46.2cm3、鎖模力需大于366.24kN， 又由于《模具設計與制造簡明手冊》表2-40選擇注射機XS-ZY-1000螺桿式注射機，其參數如下： 額定注射量：1000 螺桿直徑：85mm 注射壓力：178Mpa 鎖模力：4500KN 模板行程：700-mm 模具最大厚度：700mm 模具最小厚度：300mm 模板尺寸：700×850mm 拉桿空間：650×550mm 定位孔直徑：150mm 合模方式：液壓—機械 2.3.4 注射機有關參數的校核 （1） 最大注塑量校核 模具成型塑料制品和流道凝料總質量應小于注塑機的額定注塑量的80%，所以額定注塑量Ｍ≥138.24g÷80%=172.8g，選定的注塑機額定注塑量為1000cm3×1.76g/cm3=1760g，注塑量校核合格。 （2） 鎖模力校核 F≥kAp型=1.2*366.24KN =439.482KN，所選注塑機的鎖模力為4500KN，鎖模力校核合格。 （3） 注射壓力的校核 注射機的最大壓力應大于塑件成型所需的壓力，即 (3-7) 式中：——注射機最大注射壓力(Mpa)； ——塑件成型所需的注射壓力(Mpa)； 采用柱塞式注塑機PPA注射壓力為140～180MPa，螺桿式注塑機則取120～140MPa為宜，因此選定的注塑機的注射壓力：178 Mpa，滿足要求。 3 成型零件有關尺寸的計算 （1）型芯設計 圖3-1 型芯 型芯的尺寸計算 型芯的尺寸按以下公式計算 D=〈〔1+〕d+xΔ〉 式中D—型芯外徑尺寸 d—塑件內形尺寸 Δ—塑件公差 —塑料平均收縮率 —成形零件制造公差,取Δ/2。 （2） 型腔設計 圖3-2 型腔 1）型腔徑向尺寸按以下公式計算 D=〈〔1+〕d－xΔ〉 式中D—型腔的內形尺寸 d—塑件外形基本尺寸 Δ— 塑件公差 —塑料平均收縮率 —成形零件制造公差,取Δ/2。 2）型腔深度尺寸按以下公式計算 = 式中—型腔深度 —塑件外形高度尺寸 Δ— 塑件公差 —塑料平均收縮率 —成形零件制造公差,取 （3） 由于該產品不是透明的，所以型芯的表面粗糙度要求不需那么高。一般取Ra1.6,在機床上加工就可以直接投入使用，不需要經過其它的特殊加工?？紤]模具的修模以及型芯的磨損，在精度范圍內，型芯尺寸盡量取大值。而型腔則取大值，型腔的表面粗糟將決定產品的外觀，因此型腔的表面粗糙度則要求較高，一般取Ra0.8～0.4。在本次設計中，型腔取Ra0.8。 （4） X——綜合修正系數（考慮塑料收縮率的偏差和波動，成型零件的磨損等因素），塑件精度低、批量較小時，X取1/2；塑件精度高、批量比較大，X取3/4，根據設計要求取X為0.5。 要計算型芯、型腔的工作尺寸，必先確定塑件的公差及模具的制造公差。根據要求塑件精度取五級精度。根據塑料制件公差數值表（SJ1372—78）塑件在五級精度下，基本尺寸對應的尺寸公差如下： 表3-4 基本尺寸公差 基本尺寸㎜ 公差㎜ 基本尺寸㎜ 公差㎜ ＜3 0.16 3~6 0.18 6~10 0.20 10~14 0.22 14~18 0.24 18~24 0.28 24~30 0.32 30~40 0.36 40~50 0.40 50~65 0.46 65~80 0.52 80~100 0.60 100~120 0.68 （1）型腔：寬度方向d=240；取=0.25%（以下收縮率都取0.25%） D=[（1+0.0025）×240－0.5×0.60]=240.3 長度方向 d2’=240; D2’=[（1+0.0025）×240－0.5×0.68]=240.26 （2）型腔深度：H=66.4 ; X=0.4 H=[(1+0.0025) ×66.4+0.4×0.18]=66.638 （3）型芯： 寬度方向d=46 D=[（1+0.0025）×46+0.5×0.60]=46.415 高度方向d=64.4 D=[（1+0.0025）×64.4+0.5×0.68]=64.9 （5）型腔的強度及剛度要求 塑料模具型腔的側壁和底壁厚度計算是模具設計中經常遇到的問題，尤其對大型模具更為突出。目前常用的計算方法有按強度條件計算和按剛度條件計算兩類，但塑料模具要求既不許因強度不足而發生明顯變形，甚至破壞，也不許剛度不足而變形過大的情況，因此要求對強度和剛度加以考慮。對于型腔主要受到的力是塑料熔體的壓力，在塑料熔體的壓力作用下，型腔將產生內應力及變形。如果型腔側壁和底壁厚度不夠。當型腔中產生的內應力超過材料的許用應力時，型腔發生強度破壞，與此同時，剛度不足則發生彈性變形，從而產生溢料現象，將影響塑件成型質量，所以模具對強度和剛度都有要求。 但是，實踐證明，模具對強度和剛度的要求并非同時兼顧，對大型腔，按剛度條件，對小型腔則按強度條件計算即可。（在本設計中按強度條件來計算） 對長方形型腔壁厚和底板厚度的計算 1）型腔底板厚度： 式中——型腔內塑料熔體的壓力（MPa），一般取25~45MPa L——型腔側壁邊長（mm） b——型腔寬度（mm） B——凹模寬度（mm） [σ]——材料的許用應力，一般取100Mpa ——型腔側壁長邊尺寸（mm） =36.65mm 由于根據標準模架查得定模板的厚度為40mm，綜合各方面考慮，現確定定模板厚為40mm，可以滿足型腔的強度要求。 2）確定型腔的壁厚 表3-5 型腔壁厚關系表 型腔寬度 鑲拼式腔壁厚 40 9 ＞40～50 9～10 ＞50～60 10～11 ＞60～70 11～12 ＞70～80 12～13 ＞80～90 13～14 ＞90～100 14～15 ＞100～120 15～17 ＞120～140 17～19 ＞140～160 19～21 4 澆注系統的設計 澆注系統它是獲得優良性能和理想外觀的塑件以及最佳的成型效率有直接影響。 此塑件采用普通流道系統，它是主由流道、分流道、澆口、冷料穴組成的。澆注系統是一副模具的重要的內容之一。從總體來說，它的作用可以作如下歸納：它是將來自注塑機噴嘴的塑料熔體均勻而平穩地輸教送到型腔，同時使型腔的氣體能及時順利排出，在塑件熔體填充凝固的過程中，將注塑壓力有效地傳遞到型的各個部位，以獲得形完整、內外在質量優良的塑件制件。 澆注系統的設計的一般原則：了解塑件的成型性能和塑件熔料的流動特性。采用盡量短的流程，以降低熱量與壓力損失。澆注系統的設計應該有利于良好的排氣，澆注系統應能順利填充型腔。便于修整澆口以保證塑件外觀質量。確保均勻進料。 4.1 澆口套的選用 主流道通常位于模具中心塑料熔體的入口處，它將注射機噴嘴注射出的熔體導入分流道或型腔中。主流道的形狀為圓錐形，以便熔體的流動和開模時主流道凝料的順利拔出。主流道的尺寸直接影響到熔體的流動速度和充模時間。另外，由于其與高溫熔體及注射機噴嘴反復接觸，因此設計中常設計成可拆卸更換的澆口套。 主流道襯套為標準件可選購。主流道小端入口處與注射機噴嘴反復接觸，易磨損，對材料要求較嚴格，因而盡管小型注射?？梢詫⒅髁鞯罎部谂c定位圈設計成一個整體，但考慮上述因素通常仍然將其分開來設計，以便于拆卸更換。同時，也便于選用優質鋼材進行單獨加工和熱處理。設計中常采用碳素工具鋼（T8A或T10A），熱處理淬火表面硬度為50～55HRC，澆口套屬于標準件，在選夠澆口套時應注意：澆口套進料口直徑和球面坑半徑。因此，所選澆口套如圖所示： 圖4-1 澆口套 4.2分流道的設計 （1）分流道截面形狀 分流道截面形狀可以是圓形、半圓形、矩形、梯形和U形等，圓形和正方形截面流道的比表面積最?。鞯辣砻娣e與體積之比稱為比表面積），塑料熔體的溫度下降少，阻力亦小，流道的效率最高。但加工較困難，而且正方形截面不易脫模，所以在實際生產中較常用的截面形狀為梯形、半圓形及U形。 （2）分流道的尺寸 分流道尺寸由塑料品種、塑件的大小及長度確定。對于重量在200g以下，壁厚在3mm以下的塑件可用下面經驗公式計算分流道的直徑，如式。 D=0.2654W1/2 L1/4 式中：D---分流道的直徑，mm; W---塑件的質量，g； L---分流道的長度，mm. 此式計算的分流道直徑限于3.2mm～9.5mm.對于HPYC和PMMA。應將計算結果增加25％。對于梯形分流道，H=2D/3；對于U形分流道，H=1.25R，R=0.5D。D算出后一般取整數；對于半圓形H=0.45R 對于流動性極好的塑料（如PE，PA等），當分流道很短時，其直徑可小到2mm左右；對于流動性差的塑料（如PC，HPVC及PMMA等），分流道直徑可以大到13mm;大多數塑料所用分流道的直徑為6mm～10mm。 圖4-2 分流道布局 4.3分流道的布置 (1）在保證足夠的注塑壓力使塑料熔體順利充滿型腔的前提下，分流道截面面積與長度盡量取小值，分流道轉折處應圓弧過度。 （2）分流道較常時，在分流道的末端應開設冷料井。 （3）分流道的位置可單獨開設在定模板上或動模板上，也可以同時開設在動、定模板上，合模后形成分流道截面形狀。 （4）分流道與澆口連接處應加工成斜面，并用圓弧過度。 在單腔模中，常不設分流道，而在多腔模中，一般都設置有分流道，塑料沿分流道流動時，要求通過它盡快地充滿型腔，流動中溫度降低盡可能小，阻力盡可能低。同時，應能將塑料熔體均衡地分配到各個型腔。從前兩點出發，分流道應短而粗。但為了減少澆注系統的加回料量，分流道亦不能過粗。過粗的分流道冷卻緩慢，還倒增長模塑的周期。而該設計中使用了梯形斷面形狀的分流道。如圖所示； 圖4-3 分流道橫截面 4.4澆口設計 澆口亦稱進料口，是連接分流道與型腔的通道。它是整個澆注系統的關鍵的部位，也是最薄點。其形狀、大小及位置應根據塑件大小、形狀、壁厚、成型材料及塑件技術要求等進行而確定。澆口分限制性澆口和非限制性澆口，該塑件采用的是限制性澆口，它一方面通過截面積的突然變化，使分流道輸送來的塑料熔體的流速產生加速度，提高剪切速率，有利于塑料進入，使其充滿型腔。另一方面改善塑料熔體進入型腔的流動特性，調節澆口尺寸，可使多型腔同時充滿，可控制填充時間、冷卻時間及塑件表面質量，，同時還起著封閉型腔防止塑料熔體倒流，并便于澆口凝料與塑件分開的作用。 設計中，澆口的位置及尺寸的要求是比較嚴格的，初步試模，必要時還需要修改。因此澆口的位置的開設，對成型性能及成型質量的影響是很大的。一般在選擇澆口位置時，需要根據塑件的結構工藝及特征，成型質量和技術要求，綜合分析。一般要滿足以下原則： (1) 盡量縮短流動距離。 (2) 澆口應開設在塑件的壁厚。 (3) 必須盡量減少或避免產生熔接痕。 (4) 應有利于型腔中氣體的排除。 (5) 考慮分子定向的影響。 (6) 避免產生噴射和蠕動。 (7) 在承受彎曲沖擊載荷的部位設置澆口。 (8) 澆口位置的選擇應注意塑件的外觀質量。 澆口的形狀和尺寸對制品質量影響很大，澆口在多情況下，系整個流道斷面尺寸最小的部分（除主流道型的澆口外），一般匯報口的斷面積與分流道的斷面積之比約為0.03～0.09。斷面形狀如圖5.4所示，澆口臺階長1～1.5㎜左右．雖然澆口長度比分流道的長度短的多，但因為其斷面積甚小，澆口處的阻力與分流道相比，澆口的阻力仍然是主要的，故在加工澆口時，更應注意其尺寸的準確性。 然而，根據塑件的樣品圖、生產的批量等，采用一模四腔結構。澆口采用點澆口 具體尺寸見圖。 圖 4-4 澆點 4.5澆口位置的選擇 （1）澆口的位置的應使填充型腔的流程最短這樣的結構使壓力損失最小，易保證料流充滿整個型腔。對于型塑件，要進行流動比的校核。流動比K由流動通道的長度L與厚度t之比來確定。如下式： K=Σ（Lτ/tτ） 式中：Lτ---各段流程的長度，mm; tτ---各段流程的厚度或直徑，mm; 流動比的允許值隨塑料熔體的性質、溫度壓力等的不同而變化。流動比的計算公式為： ①K=L1/t 1+L 2+L 3/t 2 ②K= L1/t 1+L 2/t 2+L 3/t 3+2L 4/t 4+L 5/t 5 (2) 澆口位置的選擇要避免塑件變形 （3）澆口位置的設置應減少或避免產生熔接痕 熔接痕是充型時前端較冷的料流在型腔中的對接部位，它的存在會降低塑件的強度，所以設置澆口時應考慮料流的方向。為提高熔接痕處強度，可在熔接處增設溢流槽，使冷料進入逸流槽。筒形塑件采用環行澆口無熔接痕，而輪輻式澆口會有熔接痕產生。澆口的位置塑與件質量有直接影響,位置選擇不當會使塑件產生變形、熔接痕等缺陷。澆口位置的選擇如總裝圖所示。 5 合模導向機構以及定位裝置的設計 5.1導向機構的設計 本次設計采用的是簡化型三板模標準模架其中沒有導柱導向機構。其導向機構可以用大拉桿代替，大拉桿的具體設計如圖所示： 圖 5-1大拉桿 5.2定位裝置的設計 由于本設計為多分型面開模，在定模一側設置了脫澆道板，即分流道推板，故必須設置限位導柱，以便在澆注系統順利脫模后，開始進行塑件的開模及頂出，限位導柱的設計結構如圖所示： 圖 5-2限位導柱的裝配形式 限位導柱的長度由各模板厚度及開模行程決定，限位導柱的長度： L=200mm 定距螺釘?shù)闹睆剑篋=16mm 6 脫模結構的設計 在注塑成型的每一個循環中，塑件必須由模具型腔中脫出，在該設計中，為了使符合脫模機構的要求： 使塑件留于動模； 塑件不變形損壞 這是脫模機構應當達到的基本要求。要做到這一點首先必須分析塑件對模腔的附著力的大小和所在部位，以便選擇合適的脫模方式和脫模位置，使脫模力得以均勻合理的分布。 良好的塑件外觀 頂出塑件的位置應盡量設在塑件內部，以免損壞塑件的外觀。 結構可靠 因此，根據裝配圖，其模具結構的脫模機構主要由脫料板將余料打出模外，然后由司筒推動塑件使工件推出，還有在設計主型芯時也會有一定的撥模作斜度3°～5°。 本次設計的制件需要用點澆口進行入澆 這樣我們就需要設計為三板模，三板模相對普通的模具多了一個脫料板，脫料板的作用是將凝料與產品分開切斷以及將凝料打出模外。 本次設計的模具的運動過程大致如下： 開模的時候，動模板13在如圖12彈簧的作用下首先分開，這樣分流道的凝料將會被18拉料銷拉住留在14脫料板一側，當動模板13運動一定距離帶動11小拉桿的限位桿運動 從而帶動脫料板將留在脫料板一側的凝料以及主流道的余料打出模外，小拉桿運動一些距離被定模座板固定不能運動后 小拉桿拉住定模版使其靜止不動 而動模部分繼續開模運動 注塑機的頂輥作用頂桿固定板作用在復位桿上 使復位桿作用推件板運動 推件板將產品頂出模外，至此一次完整的注塑過程就完成了。 7 排氣系統的設計 塑料在熔化時，會產生氣體，所以當塑料在充滿型腔時及澆注系統內的空氣，如果在型腔中不及時排除干凈，可以會在塑件上形成氣泡、接縫、表面輪廓不清及充填缺料等缺陷。另一方面氣體的受壓產生反向壓力而降低充模速度，還可能造成塑件碳化或燒焦。注射成型時的排氣可采用如下四種方式排氣： （1） 利用配合間隙排氣； （2） 在分型面上開設排氣槽排氣； （3） 利用排氣守排氣； （4） 強制性排氣； 該模具是采用利用配合間隙排氣。其間隙值約為0.03~0.05mm.它常用于中小型的簡單模具。 8 繪制模具裝配圖以及模具的安裝試模 裝配的繪制 模具整體設計也就是模體的設計，隨著現代工業的發展，模體設計已接近標準化，可以從市場上購買相應的模體。標準模體一般包括定模板、動模板、墊塊、頂出固定板、頂板、導柱、導套、復位桿等。標準模架有12種結構，15876種規格。在本次設計中，澆口套、導柱、導套、頂桿、水嘴都采用標準件，可以外購?？傃b圖主視圖如圖所示： 圖 8-1 定模板 圖 8-2 動模板 圖 8-3 裝配三維圖 圖 8-4 總裝配二維圖 結論 為期一個學期的畢業設計即將結束，也就意味著我的大學生活即將結束，但在這一個學期的時間里我學到了很多知識和技能。 雖然每學期都安排了課程設計或者實習，但是沒有一次課程設計能與此次相比，設計限定了時間長，而且是一人一個課題要求更為嚴格，任務更加繁多、細致、要求更加嚴格、設計要求的獨立性更加高。要我們充分利用在校期間所學的課程的專業知識理解、掌握和實際運用的靈活度。在對設計的態度上的態度上是認真的積極的。 通過近一學期畢業設計的學習，給我最深的感受就是我的設計思維得到了很大的鍛煉與提高。作為一名設計人員要設計出有創意而功能齊全的產品，就必須做一個生活的有心人。多留心觀察思考我們身邊的每一個機械產品，只有這樣感性認識豐富了，才能使我們的設計思路具有創造性。 謝辭 　　　首先感謝吳國洪老師在我完成該論文過程中給予的悉心指導，指出本人設計中的錯誤與不足，使得本人能按時完成本課題的設計。并與其他同學的共同討論下，掌握了注塑模設計基本原則以及設計中對軟件的應用能力。 設計中還引用了不少工廠的經驗以及多位專家學者的著作，從中學到了很多設計技巧。使我初步認識到了以后工作中可能出現的問題，如何去解決，這將對我以后的工作有很好的幫助作用，在這里一并表示感謝。 最后，通過本設計我鞏固了所學專業知識，并得到了不少心得。但由于是第一次系統的做這樣規模的設計，會有不少缺點和錯誤，歡迎審核答辯的老師批評指正，在此再次表示感謝。 參考文獻 [1] 黃毅宏 模具制造工藝. 北京：機械工業出版社 1999 [2] 周四新,和清芳 Pro/ENGINEER野火版基礎設計. 北京:機械工業出版社 2004 [3] 中國機械工業教育協會組編 塑料模設計與制造. 北京:機械工業出版社 2005 [4] 馬廣、王志明 模具CAD/CAM項目化實訓教程. 北京：科學出版社 2009 [5] 伍先明等 塑料模具設計指導. 北京：國防工業出版社 2006.5 [6] 李學鋒等 模具設計與制造實訓教程. 北京：化學工業出版社 2004 [7] 黃虹 塑料成型加工與模具. 北京：化學工業出版社 2006 英文原文 Session VA4 I ntelligent Mold Design Tool For Plastic Injection Molding Jagannath Yammada, Terrence L. Chambers, Suren N. Dwivedi Department of Mechanical Engineering University of Louisiana at Lafayette Abstract Plastic Injection molding is one of the most popular manufacturing processes for making thermoplastic products, and mold design is a key aspect of the process. Design of molds requires knowledge, expertise and most importantly experience in the field. When one of these is lacking, selection of an appropriate mold for manufacturing a plastic component is done on a trial-and-error basis. This increases the cost of production and introduces inconsistencies in the design. This paper describes the development of an intelligent mold design tool. The tool captures knowledge about the mold design process and represents the knowledge in logical fashion. The knowledge acquired will be deterministic and non-deterministic information about the mold design process. Once developed the mold design tool will guide the user in selecting an appropriate mold for his plastic part based on various client specifications. Introduction The plastic injection molding process demands knowledge, expertise and, most important, experience for its successful implementation. Often it is the molding parameters that control the efficiency of the process. Effectively controlling and optimizing these parameters during themanufacturing process can achieve consistency, which takes the form of part quality and part cost. The level of experience of the manufacturer(s) determines how effectively the process parameters are controlled. This sometimes leads to inconsistency introduced by human error. There is also the case where there is inexperience, shortage of time, resources and little scope for innovation. Knowledge-based engineering provides a feasible solution to all these problems by creating what is called an “intelligent model” of the problem. 1 IKEM Intelligent Knowledge based Engineering modules for the plastic injection molding process (IKEM) is a software technology that is a step ahead of the concurrent engineering and CAD/CAM systems. It integrates current knowledge about the design and manufacturing processes and helps to reduce several man-hours by reducing engineering changes in the design phase of product development by giving users instruction about various design aspects. The system will be used for injection molding design, design iterations, and process integration. The current process consists of many manual computations, CAD graphical constructions, and experience attained from previous projects. Once the engineer completes the design, it will be evaluated for performance. The IKEM project has been divided into three major modules. 1. The cost estimation module 2. The mold design module 3. The Manufacturing module Input to the IKEM system is of two forms. Input in the form of a CAD model (Pro-E file) and input given at the User Interface form. Figure 1 illustrates the kind of input that goes into each module and the output given to the user. Figure 1. Organization of the IKEM Project 2 Intelligent Mold Design Tool The mold design tool in its basic form is a Visual Basic application taking input from a text file that contains information about the part and a User Input form. The text file contains information about the part geometry parsed from a Pro/E information file. The input is used to estimate the dimensions of mold and variousother features. 2.1 Literature Review Design of molds is another stage of the injection molding process where the experience of an engineer largely helps automate the process and increase its efficiency. The issue that needs attention is the time that goes into designing the molds. Often, design engineers refer to tables and standard handbooks while designing a mold, which consumes lot of time. Also, a great deal of time goes into modeling components of the mold in standard CAD software. Differen researchers have dealt with the issue of reducing the time it takes to design the mold in different ways. Koelsch and James have employed group technology techniques to reduce the mold design time. A unique coding system that groups a class of injection molded parts, and the tooling required ininjection molding is developed which is general and can be applied to other product lines. A software system to implement the coding system has also been developed. Attempts were also directed towards the automation of the mold design process by capturing experience and knowledge of engineers in the field. The development of a concurrent mold design system is one such approach that attempts to develop a systematic methodology for injection mold design processes in a concurrent engineering environment. The objective of their research was to develop a mold development process that facilitates concurrent engineering-based practice, and to develop a knowledge-based design aid for injection molding mold design that accommodates manufacturability concerns, as well as product requirements. Researchers have been trying to automate the mold design process either by capturing only the deterministic information on the mold design process or the non-deterministic information, in various ways. This research uniquely attempts to develop a mold design application that captures information in both forms; deterministic and non-deterministic. 2.2 Approach Adopted In order to develop an intelligent mold design tool, the conventional method of designing molds is studied. The application developer and the design engineer work together in designing a mold for a particular plastic part. During this time, the approach adopted by the engineer to select the mold base is closely observed and aspects of the selection process that require his knowledge/experience are identified. Also, there will be times when the engineer will refer to tables and handbooks in order to standardize his selection process. This time consuming process is also recorded to incorporate it later in the application. Formulating the problem for the application in terms of inputs and outputs is the next stage. This involves defining what information about the mold layout is most required for the user and also the minimum number of inputs that can be taken from him to give those outputs. In injection molding, the polymer melt at high temperature is injected into the mold under high pressure [1]. Thus, the mold material needs to have thermal and mechanical properties capable of withstanding the temperatures and pressures of the molding cycle. The focus of many studies has been to create the injection mold directly by a rapid prototyping (RP) process. By eliminating multiple steps, this method of tooling holds the best promise of reducing the time and cost needed to create low-volume quantities of parts in a production material. The potential of integrating injection molding with RP technologies has been demonstrated many times. The properties of RP molds are very different from those of traditional metal molds. The key differences are the properties of thermal conductivity and elastic modulus (rigidity). For example, the polymers used in RP-fabricated stereolithography (SL) molds have a thermal conductivity that is less than one thousandth that of an aluminum tool. In using RP technologies to create molds, the entire mold design and injection-molding process parameters need to be modi?ed and optimized from traditional methodologies due to the completely different tool material. However, there is still not a fundamental understanding of how the modi?cations to the mold tooling method and material impact both the mold design and the injection molding process parameters. One cannot obtain reasonable results by simply changing a few material properties in current models. Also, using traditional approaches when making actual parts may be generating sub-optimal results. So there is a dire need to study the interaction between the rapid tooling (RT) process and material and injection molding, so as to establish the mold design criteria and techniques for an RT-oriented injection molding process. In addition, computer simulation is an effective approach for predicting the quality of molded parts. Commercially available simulation packages of the traditional injection molding process have now become routine tools of the mold designer and process engineer [2]. Unfortunately, current simulation programs for conventional injection molding are no longer applicable to RP molds, because of the dramatically dissimilar tool material. For instance, in using the existing simulation software with aluminum and SL molds and comparing with experimental results, though the simulation values of part distortion are reasonable for the aluminum mold, results are unacceptable, with the error exceeding 50%. The distortion during injection molding is due to shrinkage and warpage of the plastic part, as well as the mold. For ordinarily molds, the main factor is the shrinkage and warpage of the plastic part, which is modeled accurately in current simulations. But for RP molds, the distortion of the mold has potentially more in?uence, which have been neglected in current models. For instance, [3] used a simple three-step simulation process to consider the mold distortion, which had too much deviation. In this paper, based on the above analysis, a new simulation system for RP molds is developed. The proposed system focuses on predicting part distortion, which is dominating defect in RP-molded parts. The developed simulation can be applied as an evaluation tool for RP mold design and process optimization. Our simulation system is veri?ed by an experimental example. Although many materials are available for use in RP technologies, we concentrate on using stereolithography (SL), the original RP technology, to create polymer molds. The SL process uses photopolymer and laser energy to build a part layer by layer. Using SL takes advantage of both the commercial dominance of SL in the RP industry and the subsequent expertise base that has been developed for creating accurate, high-quality parts. Until recently, SL was primarily used to create physical models for visual inspection and form-?t studies with very limited functional applications. However, the newer generation stereolithographic photopolymers have improved dimensional, mechanical and thermal properties making it possible to use them for actual functional molds. Based on the information gathered in the mold design exercise, the conventions followed by the engineer are transformed into if-then rules. Decision tables are used to account for all possible cases that arise when dealing with a particular aspect of the mold design process. The rules so framed are then organized into modules interacting with each other, using an application development environment. Finally the application is tested for its validity when it comes to designing molds for plastic parts manufactured in the industry. 2.3 Selection of Appropriate Mold Base Typically, selection of appropriate mold base for manufacturing a plastic part involves Estimating the number of cavities The number of cavities is decided depending on the number of parts required within a given time. There are also other issues like the plasticizing capacity of the machine, reject rate etc that affect the number of cavities to be present in the mold base. Deciding on the presence of inserts and their dimensions Inserts facilitate the reusability of the mold base and therefore help in reducing cost of manufacturing. When it comes to selecting the dimensions and the number, a decision is made depending on the reusability of existing old inserts and cost of ordering new ones. Determining the size and location of runners The runner size depends on the material being molded. Although there are other considerations material properties determines the channel size required for its flow. Location of runners mainly depends on the topology of runners being used. Though a circular runner system is always preferable, the branched runner system that avoids runner balancing is the one most widely used. Determining the diameter of sprue The diameter of the sprue is decided based on the size of the mold, number of cavities, or the amount of plastic that is to be filled within a given time. Locating gates Plastic enters the cavity at a point where it can uniformly fill the cavity. A gate can be located at any point on the perimeter of a circular cavity but has to enter at the midsection when it comes to filling rectangular cavities. Determining the size and location of water lines Water lines are located at standard distances form each other and from any wall in the mold. The convention is not to locate a waterline within one diameter range on the mold wall. Deciding mold dimensions based on above conclusions Based on all the above decisions the approximate mold dimensions can be estimated and rounded off to the nearest catalog number. Considering all the above aspects before even modeling the mold base reduces the cost and time that go into redesigning. The emergence of mold can be traced back thousands of years ago, pottery and bronze foundry, but the large-scale use is with the rise of modern industry and developed.The 19th century, with the arms industry (gun's shell), watch industry, radio industry, dies are widely used. After World War II, with the rapid development of world economy, it became a mass production of household appliances, automobiles, electronic equipment, cameras, watches and other parts the best way. From a global perspective, when the United States in the forefront of stamping technology - many die of advanced technologies, such as simple mold, high efficiency, mold, die and stamping the high life automation, mostly originated in the United States; and Switzerland, fine blanking, cold in Germany extrusion technology, plastic processing of the Soviet Union are at the world advanced. 0's, mold industry focus is based on subscriber demand, production can meet the product requirements of the mold. Multi-die design rule of thumb, reference has been drawing and perceptual knowledge, on the design of mold parts of a lack of real understanding of function. From 1955 to 1965, is the pressure processing of exploration and development of the times - the main components of the mold and the stress state of the function of a mathematical sub-bridge, and to continue to apply to on-site practical knowledge to make stamping technology in all aspects of a leap in development. The result is summarized mold design principles, and makes the pressure machine, stamping materials, processing methods, plum with a structure, mold materials, mold manufacturing method, the field of automation devices, a new look to the practical direction of advance, so that pressing processing apparatus capable of producing quality products from the first stage. Into the 70's to high speed, launch technology, precision, security, development of the second stage. Continue to emerge in this process a variety of high efficiency, business life, high-precision multi-functional automatic school to help with. Represented by the number of working places as much as other progressive die and dozens of multi-station transfer station module. On this basis, has developed both a continuous pressing station there are more slide forming station of the press - bending machine. In the meantime, the Japanese stand to the world's largest - the mold into the micron-level precision, die life, alloy tool steel mold has reached tens of millions of times, carbide steel mold to each of hundreds of millions of times p minutes for stamping the number of small presses usually 200 to 300, up to 1200 times to 1500 times. In the meantime, in order to meet product updates quickly, with the short duration (such as cars modified, refurbished toys, etc.) need a variety of economic-type mold, such as zinc alloy die down, polyurethane rubber mold, die steel skin, also has been very great development. From the mid-70s so far can be said that computer-aided design, supporting the continuous development of manufacturing technology of the times. With the precision and complexity of mold rising, accelerating the production cycle, the mold industry, the quality of equipment and personnel are required to improve. Rely on common processing equipment, their experience and skills can not meet the needs of mold. Since the 90's, mechanical and electronic technologies in close connection with the development of NC machine tools, such as CNC wire cutting machine, CNC EDM, CNC milling, CNC coordinate grinding machine and so on. The use of computer automatic programming, control CNC machine tools to improve the efficiency in the use and scope. In recent years, has developed a computer to time-sharing by the way a group of direct management and control of CNC machine tools NNC system. With the development of computer technology, computers have gradually into the mold in all areas, including design, manufacturing and management. International Association for the Study of production forecasts to 2000, as a means of links between design and manufacturing drawings will lose its primary role. Automatic Design of die most fundamental point is to establish the mold standard and design standards. To get rid of the people of the past, and practical experience to judge the composition of the design center, we must take past experiences and ways of thinking, for series, numerical value, the number of type-based, as the design criteria to the computer store. Components are dry because of mold constitutes a million other differences, to come up with a can adapt to various parts of the design software almost impossible. But some products do not change the shape of parts, mold structure has certain rules, can be summed up for the automatic design of software. If a Japanese company's CDM system for progressive die design and manufacturing, including the importation of parts of the figure, rough start, strip layout, determine the size and standard templates, assembly drawing and parts, the output NC program (for CNC machining Center and line cutting program), etc., used in 20% of the time by hand, reduce their working hours to 35 hours; from Japan in the early 80s will be three-dimensional cad / cam system for automotive panel die. Currently, the physical parts scanning input, map lines and data input, geometric form, display, graphics, annotations and the data is automatically programmed, resulting in effective control machine tool control system of post-processing documents have reached a high level; computer Simulation (CAE) technology has made some achievements.At high levels, CAD / CAM / CAE integration, that data is integrated, can transmit information directly with each other. Achieve network. Present.Only a few foreign manufacturers can do it. 2.4 Formulation of the Problem Based on issues that require human knowledge/experience, and aspects of mold design that consume time referring to tables, data sheets etc., the problem for developing the application is defined as shown in Figure 2. While most of the input, like the number of cavities, cavity image dimensions, cycle time are based on the client specifications, other input like the plasticizing capacity, shots per minute etc., can be obtain