裝配圖復合形法減速器優化設計

裝配圖復合形法減速器優化設計,裝配,復合,減速器,優化,設計 單級圓柱齒輪減速器復合形法fortran優化源程序 C ============== PROGRAM COMPLE C ============== DIMENSION X(25),GX(50),XCOM(1250) COMMON /ONE/ ITE,IXE,ILI,NPE,NFX,NGR READ(*,*) N,KG,K WRITE(*,10001) N,KG,K 10001 FORMAT(25X,'========== PRIMARY DATA =========='//5X, 1 'N=',I4,5X,'KG=',I4,5X,'K=',I4) CALL MAISUB(N,K,KG,X,GX,XCOM) STOP END C =================================== SUBROUTINE MAISUB(N,K,KG,X,GX,XCOM) C =================================== DIMENSION X(N),GX(KG),XCOM(N,K),FXK(50),XR(25) DIMENSION XO(25),XH(25),XL(25),BL(25),BU(25) COMMON /ONE/ ITE,IXE,ILI,NPE,NFX,NGR COMMON /TWO/ ISE READ(*,*) (X(I),I=1,N) READ(*,*) EPS READ(*,*) KWR,ISE READ(*,*) (BL(I),I=1,N),(BU(I),I=1,N) WRITE(*,1010) (BL(I),I=1,N) WRITE(*,1015) (BU(I),I=1,N) WRITE(*,1020) EPS 1010 FORMAT(' BL:'/(5X,5E15.6)) 1015 FORMAT(' BU:'/(5X,5E15.6)) 1020 FORMAT(5X,'EPS=',E10.2) ITE=0 NFX=0 IXE=0 RM=2657863.0 1025 CALL PRICOM(N,K,KG,X,GX,XCOM,FXK,BL,BU,RM) IF(KWR.LT.0) GOTO 1041 WRITE(*,1030) 1030 FORMAT(/25X,'========== PRIMARY COMPLEX =========='/) WRITE(*,1080) K DO 1031 L=1,K WRITE(*,1085) L,(XCOM(I,L),I=1,N) 1031 CONTINUE WRITE(*,1035) (FXK(I),I=1,K) 1035 FORMAT(4X,'FXK:'/(5X,5E15.6)) 1041 WRITE(*,1042) 1042 FORMAT(/25X,'========== ITEATION COMPUTE =========='/) 1045 ITE=ITE+1 CALL FXSEGU(N,K,XCOM,FXK) DO 1050 I=1,N 1050 XL(I)=XCOM(I,K) FXL=FXK(K) SDX=0.0 DO 1055 I=1,K-1 1055 SDX=SDX+(FXL-FXK(I))**2 =SQRT(SDX/FLOAT(K-1)) IF(SDX.LE.EPS) GOTO 1210 IF(KWR.GT.0) GOTO 1056 IF(ITE/10*10.NE.ITE) GOTO 1090 1056 WRITE(*,1060) ITE,FXL IF(KWR.LT.0) GOTO 1090 WRITE(*,1065) (XL(I),I=1,N) WRITE(*,1070) FXL WRITE(*,1075) (GX(I),I=1,KG) WRITE(*,1035) (FXK(I),I=1,K) 1060 FORMAT(/1X,'***** ITE=',I4,5X,'FXL=',E15.7) 1065 FORMAT(' X :'/(5X,5E15.6)) 1070 FORMAT(' FX:'/(5X,5E15.6)) 1075 FORMAT(' GX:'/(5X,5E15.6)) 1080 FORMAT(' XCOM: (K=',I3,')') 1085 FORMAT(2X,I2/(5X,5E15.6)) 1090 LH=1 1095 DO 1100 I=1,N 1100 XH(I)=XCOM(I,LH) FXH=FXK(LH) CALL XCENTE(N,K,K,LH,XO,XCOM) CALL FFX(N,XO,FXO) CALL GGX(N,KG,XO,GX) DO 1105 J=1,KG IF(GX(J).GE.0.0) GOTO 1170 1105 CONTINUE 1140 PHI=1.3 1145 DO 1150 I=1,N 1150 XR(I)=XO(I)+PHI*(XO(I)-XH(I)) CALL FFX(N,XR,FXR) CALL GGX(N,KG,XR,GX) DO 1151 J=1,KG IF(GX(J).GE.0.0) GOTO 1152 1151 CONTINUE GOTO 1155 1152 PHI=0.5*PHI GOTO 1145 1155 IF(FXR.LT.FXH) GOTO 1160 IF(PHI.LE.1E-10) GOTO 1195 PHI=0.5*PHI GOTO 1145 1160 DO 1165 I=1,N 1165 XCOM(I,LH)=XR(I) FXK(LH)=FXR GOTO 1045 1170 DO 1175 I=1,N BL(I)=XL(I) BU(I)=XO(I) 1175 CONTINUE DO 1180 I=1,N 1180 X(I)=XL(I) ISE=1 GOTO 1025 1195 LH=LH+1 WRITE(*,1200) LH 1200 FORMAT(1X,'****** LH=',I2,'*****') IF(LH.LE.K/2) GOTO 1095 WRITE(*,1205) 1205 FORMAT(/25X,'********** ITERTION ABORTIVE **********'/) GOTO 1220 1210 WRITE(*,1215) 1215 FORMAT(/25X,'========== OPTIMUM SOLUTION =========='/) 1220 WRITE(*,1225) ITE,NFX,IXE 1225 FORMAT(' ITE=',I5,' NFX=',I5' IXE=',I5) WRITE(*,1065) (XL(I),I=1,N) WRITE(*,1070) FXL WRITE(*,1075) (GX(I),I=1,KG) RETURN END C ================================================ SUBROUTINE PRICOM(N,K,KG,X,GX,XCOM,FXK,BL,BU,RM) C ================================================ DIMENSION X(N),XO(25),BL(N),BU(N),GX(KG),XCOM(N,K),FXK(K) COMMON /TWO/ ISE 2020 IF(ISE) 2025,2050,2075 2025 WRITE(*,2019) 2019 FORMAT(5X,'READ XCOM (FORMAT: * )') READ(*,*) ((XCOM(I,J),I=1,N),J=1,K) DO 2045 L=1,K DO 2030 I=1,N 2030 X(I)=XCOM(I,L) CALL FFX(N,X,FXK(L)) CALL GGX(N,KG,X,GX) DO 2031 J=1,KG IF(GX(J).GE.0.0) GOTO 2075 2031 CONTINUE 2045 CONTINUE RETURN 2050 CALL FFX(N,X,FXK(1)) CALL GGX(N,KG,X,GX) DO 2051 L=1,KG IF(GX(L).GE.0.0) GOTO 2075 2051 CONTINUE GOTO 2095 2075 DO 2080 I=1,N CALL RANDOM(RM,Q) 2080 X(I)=BL(I)+Q*(BU(I)-BL(I)) CALL FFX(N,X,FXK(1)) CALL GGX(N,KG,X,GX) DO 2081 L=1,KG IF(GX(L).GE.0.0) GOTO 2075 2081 CONTINUE 2095 DO 2100 I=1,N 2100 XCOM(I,1)=X(I) DO 2110 L=2,K DO 2105 I=1,N CALL RANDOM(RM,Q) XCOM(I,L)=BL(I)+Q*(BU(I)-BL(I)) 2105 CONTINUE 2110 CONTINUE LH=0 DO 2155 LL=1,K-1 LL2=LL CALL XCENTE(N,K,LL2,LH,XO,XCOM) CALL FFX(N,XO,FXO) CALL GGX(N,KG,X,GX) DO 2111 L=1,KG IF(GX(L).GE.0.0) GOTO 2075 2111 CONTINUE 2115 CONTINUE LL1=LL+1 DO 2120 I=1,N 2120 X(I)=XCOM(I,LL1) 2125 CALL FFX(N,X,FXK(LL1)) CALL GGX(N,KG,X,GX) DO 2126 L=1,KG IF(GX(L).GE.0.0) GOTO 2145 2126 CONTINUE DO 2140 I=1,N 2140 XCOM(I,LL1)=X(I) GOTO 2155 2145 DO 2150 I=1,N 2150 X(I)=XO(I)+0.5*(X(I)-XO(I)) GOTO 2125 2155 CONTINUE RETURN END C =============================== SUBROUTINE FXSEGU(N,K,XCOM,FXK) C =============================== DIMENSION X(25),XCOM(N,K),FXK(K) DO 3010 L=1,K-1 KL=K-L DO 3005 LP=1,KL LP1=LP+1 IF(FXK(LP).GT.FXK(LP1)) GOTO 3005 W=FXK(LP) FXK(LP)=FXK(LP1) FXK(LP1)=W DO 3000 I=1,N X(I)=XCOM(I,LP) XCOM(I,LP)=XCOM(I,LP1) 3000 XCOM(I,LP1)=X(I) 3005 CONTINUE 3010 CONTINUE RETURN END C ==================================== SUBROUTINE XCENTE(N,K,LL,LH,XO,XCOM) C ==================================== DIMENSION XO(N),XCOM(N,K) COMMON /ONE/ ITE,IXE,ILI,NPE,NFX,NGR IXE=IXE+1 DO 4015 I=1,N XS=0.0 DO 4000 L=1,LL IF(L.EQ.LH) GOTO 4000 XS=XS+XCOM(I,L) 4000 CONTINUE IF(LH) 4010,4010,4005 4005 XO(I)=XS/FLOAT(LL-1) GOTO 4015 4010 XO(I)=XS/FLOAT(LL) 4015 CONTINUE RETURN END SUBROUTINE RANDOM(RM,Q) C ======================= C ======================= RM35=2.0**35 RM36=2.0*RM35 RM37=2.0*RM36 RM =5.0*RM IF(RM.GE.RM37) RM=RM-RM37 IF(RM.GE.RM36) RM=RM-RM36 IF(RM.GE.RM35) RM=RM-RM35 Q=RM/RM35 RETURN END 一、選題的依據及意義： 隨著社會的發展和人民生活水平的提高，人們對產品的需求是多樣化的，這就決定了未來的生產方式趨向多品種、小批量。在各行各業中十分廣泛地使用著齒輪減速器，它是一種不可缺少的機械傳動裝置. 它是機械設備的重要組成部分和核心部件。目前，國內各類通用減速器的標準系列已達數百個，基本可滿足各行業對通用減速器的需求。國內減速器行業重點骨干企業的產品品種、規格及參數覆蓋范圍近幾年都在不斷擴展，產品質量已達到國外先進工業國家同類產品水平，承擔起為國民經濟各行業提供傳動裝置配套的重任，部分產品還出口至歐美及東南亞地區，推動了中國裝配制造業發展。 圓柱齒輪減速器是一種使用非常廣泛的機械傳動裝置。減速器是用于原動機與工作機之間的獨立的傳動裝置，用來降低轉速和增大轉矩，以滿足工作需要。在現代機械中應用極為廣泛，具有品種多、批量小、更新?lián)Q代快的特點。目前生產的各種類型的減速器還存在著體積大、重量重、承載能力低、成本高和使用壽命短等問題，與國外先進產品相比還有較大的差距。對減速器進行優化設計，選擇最佳參數是提高承載能力、減輕重量和降低成本等各項指標的一種重要途徑。 目的： 通過設計熟悉機器的具體操作，增強感性認識和社會適應能力，進一步鞏固、 深化已學過的理論知識，提高綜合運用所學知識發現問題、解決問題的能力。學習機械設計的一般方法，掌握通用機械零件、機械傳動裝置或簡單機械的設計原理和過程。對所學技能的訓練，例如：計算、繪圖、查閱設計資料和手冊，運用標準和規范等。學會利用多種手段(工具)解決問題，如：在本設計中可選擇CAD等制圖工具。了解減速器內部齒輪間的傳動關系。 意義： 通過設計，培養學生理論聯系實際的工作作風，提高分析問題、解決問題的獨立工作能力；通過實習，加深學生對專業的理解和認識，為進一步開拓專業知識創造條件，鍛煉動手動腦能力，通過實踐運用鞏固了所學知識，加深了解其基本原理 二、國內外研究概況及發展趨勢（含文獻綜述）： 1、國外減速器技術發展簡況 齒輪減速器在各行各業中十分廣泛地使用著，是一種不可缺少的機械傳動裝置。當前減速器普遍存在著體積大、重量大，或者傳動比大而機械效率過低的問題。 國外的減速器，以德國、丹麥和日本處于領先地位，特別在材料和制造工藝方面占據優勢，減速器工作可靠性好，使用壽命長。但其傳動形式仍以定軸齒輪傳動為主，體積和重量問題，也未解決好。最近報導，日本住友重工研制的FA型高精度減速器，美國Alan-Newton公司研制的X-Y式減速器，在傳動原理和結構上與本項目類似或相近，都為目前先進的齒輪減速器。當今的減速器是向著大功率、大傳動比、小體積、高機械效率以及使用壽命長的方向發展。因此，除了不斷改進材料品質、提高工藝水平外，還在傳動原理和傳動結構上深入探討和創新，平動齒輪傳動原理的出現就是一例。減速器與電動機的連體結構，也是大力開拓的形式，并已生產多種結構形式和多種功率型號的產品。 目前，超小型的減速器的研究成果尚不明顯。在醫療、生物工程、機器人等領域中，微型發動機已基本研制成功，美國和荷蘭近期研制的分子發動機的尺寸在納米級范圍，如能輔以納米級的減速器，則應用前景遠大。 2、國內減速器技術發展簡況 國內的減速器多以齒輪傳動、蝸桿傳動為主，但普遍存在著功率與重量比小，或者傳動比大而機械效率過低的問題。另外，材料品質和工藝水平上還有許多弱點，特別是大型的減速器問題更突出，使用壽命不長。國內使用的大型減速器(500kw以上)，多從國外(如丹麥、德國等)進口，花去不少的外匯。60年代開始生產的少齒差傳動、擺線針輪傳動、諧波傳動等減速器具有傳動比大，體積小、機械效率高等優點?。但受其傳動的理論的限制，不能傳遞過大的功率，功率一般都要小于40kw。由于在傳動的理論上、工藝水平和材料品質方面沒有突破，因此，沒能從根本上解決傳遞功率大、傳動比大、體積小、重量輕、機械效率高等這些基本要求。90年代初期，國內出現的三環(齒輪)減速器，是一種外平動齒輪傳動的減速器，它可實現較大的傳動比，傳遞載荷的能力也大。它的體積和重量都比定軸齒輪減速器輕，結構簡單，效率亦高。由于該減速器的三軸平行結構，故使功率/體積(或重量)比值仍小。且其輸入軸與輸出軸不在同一軸線上，這在使用上有許多不便。北京理工大學研制成功的"內平動齒輪減速器"不僅具有三環減速器的優點外，還有著大的功率/重量(或體積)比值，以及輸入軸和輸出軸在同一軸線上的優點，處于國內領先地位。國內有少數高等學校和廠礦企業對平動齒輪傳動中的某些原理做些研究工作，發表過一些研究論文，在利用擺線齒輪作平動減速器開展了一些工作。二、平動齒輪減速器工作原理簡介,平動齒輪減速器是指一對齒輪傳動中，一個齒輪在平動發生器的驅動下作平面平行運動，通過齒廓間的嚙合，驅動另一個齒輪作定軸減速轉動，實現減速傳動的作用。平動發生器可采用平行四邊形機構，或正弦機構或十字滑塊機構。本成果采用平行四邊形機構作為平動發生器。平動發生器可以是虛擬的采用平行四邊形機構，也可以是實體的采用平行四邊形機構。有實用價值的平動齒輪機構為內嚙合齒輪機構，因此又可以分為內齒輪作平動運動和外齒輪作平動運動兩種情況。外平動齒輪減速機構，其內齒輪作平動運動，驅動外齒輪并作減速轉動輸出。該機構亦稱三環(齒輪)減速器。由于內齒輪作平動，兩曲柄中心設置在內齒輪的齒圈外部，故其尺寸不緊湊，不能解決體積較大的問題。?內平動齒輪減速，其外齒輪作平動運動，驅動內齒輪作減速轉動輸出。由于外齒輪作平動，兩曲柄中心能設置在外齒輪的齒圈內部，大大減少了機構整體尺寸。由于內平動齒輪機構傳動效率高、體積小、輸入輸出同軸線，故由廣泛的應用前景。? 三、本項目的技術特點與關鍵技術? 1.本項目的技術特點,本新型的"內平動齒輪減速器"與國內外已有的齒輪減速器相比較，有如下特點：(1)傳動比范圍大，自I=10起，最大可達幾千。若制作成大傳動比的減速器，則更顯示出本減速器的優點。(2)傳遞功率范圍大：并可與電動機聯成一體制造。(3)結構簡單、體積小、重量輕。比現有的齒輪減速器減少1/3左右。(4)機械效率高。嚙合效率大于95%，整機效率在85%以上，且減速器的效率將不隨傳動比的增大而降低，這是別的許多減速器所不及的。 (5)本減速器的輸入軸和輸出軸是在同一軸線上 三、研究?jī)?nèi)容及實驗方案： 研究?jī)?nèi)容： 1.采用復合形法，以體積最小為目標進行減速器優化設計； 2.與常規設計結果進行比較分析， 3.繪制減速器裝配圖及主要零件圖。 實驗方案： 1. 收集有關資料寫開題報告 2. 以減速器體積最小為目標函數建立優化設計的數學模型 3．采用復合型法編寫優化設計程序、計算 4. 計算減速器各項尺寸，并進行結果分析 5. 運用UG繪制減速器裝配圖及主要零件圖 6. 翻譯外文資料 7.撰寫畢業設計論文 四、目標、主要特色及工作進度 目標：本課題以減速器體積最小為目標函數，設計減速器的最優參數， 繪制減速器裝配圖及主要零件圖。 主要特色：減速器體積小，重量輕，承載能力提高，降低成本 工作進度： 1. 收集資料、開題報告、外文翻譯 3，01-3.21 2. 建立優化設計的數學模型 3.22-4.04 3．編寫優化設計程序、計算 4.05-5.09 4. 減速器常規設計計算、結果分析 5.09-5.23 5. 繪制減速器裝配圖及主要零件圖 5.24-6.13 6. 撰寫畢業設計論文 6.14-6.27 7. 答辯準備及論文答辯 6.28-7.02 五、參考文獻 【1】璞良貴，紀名剛主編.機械設計.第八版.北京：高等教育出版社，2007 【2】孫靖民主編.機械優化設計.第三版.北京：機械工業出版社，2005 【3】方世杰，綦耀光主編.機械優化設計.北京：機械工業出版社，1997.2 【4】王昆等主編. 機械設計課程設計手冊.北京：機械工業出版社，2004 【5】劉瑞新，洪遠征等編著.Visual Basic 程序設計教程.第二版. 北京：機械工業出版社，2006 【6】楊黎明主編.機械零件設計手冊.北京：國防工業出版社，1996 【7】劉瑞新，洪遠征等編著.Visual Basic 程序設計教程上機指導及習題解答.第二版. 北京：機械工業出版社，2006 【8】鄭貞平，喻德主編.UG NX5中文版三維設計與NC加工實例精解. 北京：機械工業出版社，2008 【9】Carrol, R., and Johnson, G.,“Optimal design of compact spur gear sets”, ASME Journal of mechanisms, transmissions and automation in design. Vol.106, No.1, March 1984, pp.95-101 復合形法減速器優化設計 學生姓名: 戴曉思 班級: 078105206 指導老師: 朱保利 摘要：圓柱齒輪減速器是一種使用非常廣泛的機械傳動裝置。減速器是用于原動機與工作機之間的獨立的傳動裝置，用來降低轉速和增大轉矩，以滿足工作需要。在現代機械中應用極為廣泛，具有品種多、批量小、更新?lián)Q代快的特點。目前生產的各種類型的減速器還存在著體積大、重量重、承載能力低、成本高和使用壽命短等問題，與國外先進產品相比還有較大的差距。對減速器進行優化設計，選擇最佳參數是提高承載能力、減輕重量和降低成本等各項指標的一種重要途徑。 單級圓柱齒輪減速器優化設計主要是通過計算機輔助設計，利用fortran語言進行編程優化。本課題以減速器最大尺寸最小或重量最輕為目標函數，設計減速器的最優參數，研究?jī)?nèi)容：采用復合形法，以體積最小為目標進行減速器優化設計，與常規設計結果進行比較分析，繪制減速器3d裝配圖及主要零件圖 此次設計的減速器與常規設計比較具有體積小，重量輕，結構緊湊，成本低等問題。編程方法簡單，能夠很好的達到優化效果，能夠運用到工程實際中去。 關鍵字： 單級圓柱齒輪減速器、優化設計、fortran、復合型法、體積、 3d設計 指導教師簽名： optimal design of reliability for the single-stage helical cylinder gear reducer Student name: Dai Xiaosi Class：0781052 Supervisor: Professor Zhu Baoli Abstract: The wheels gear is a very extensive use of automatic transmission. gear is used for the original motion and the work of the independence of the transmission that is used to reduce speed and torques increase in turn, need to work. in modern machinery used in a wide variety and quantity of small and fast. the upgrading of the production of various kinds of gear have a great volume and weight bearing ability, heavy and low cost and high and use a shorter life span, And advanced product compare there is a large gap. the gear design and optimize the choice of the parameter is to improve the bearing ability, lighten the weight and reduce costs for all the way. This column with the main gear design is a computer-aided design and optimize the use of fortran programming language. this subject in order to gear the maximum size to the weight or the light of objective function, the design of gear and study the contents of a composite image ：, to save the goal of gear design and optimize the conventional design a comparative analysis, gear and main parts of the assembly drawing The design of gear and conventional design are a small volume, light weight, compact structure, low cost etc. a programming method is simple to very good to achieve the effect can be applied to the actual. Keyword: A homopolar bevel gear speed reducer optimizing design fortran complex method volume 3d design Signature of conductor: ELEMENTS OF CAM DESIGN How to plan and produce simple but efficient cams for petrol engines and other mechanisms Cams are among the most versatile mechanisms available．A cam is a simple two-member device．The input member is the cam itself，while the output member is called the follower．Through the use of cams，a simple input motion can be modified into almost any conceivable output motion that is desired．Some of the common applications of cams are ——Camshaft and distributor shaft of automotive engine ——Production machine tools ——Automatic record players ——Printing machines ——Automatic washing machines ——Automatic dishwashers The contour of high-speed cams (cam speed in excess of 1000 rpm) must be determined mathematically．However，the vast majority of cams operate at low speeds(less than 500 rpm) or medium-speed cams can be determined graphically using a large-scale layout．In general，the greater the cam speed and output load，the greater must be the precision with which the cam contour is machined． Cams in some form or other are essential to the operation of many kinds of mechanical devices. Their best-known application is in the valve-operating gear of internal combustion engines, but they play an equally important part in industrial machinery, from printing presses to reaping machines. In general, a cam can be defined as a projection on the face of a disc or the surface of a cylinder for the purpose of producing intermittent reciprocating motion of a contacting member or follower. Most cams operate by rotary motion, but this is not an essential condition and in special cases the motion may be semi-rotary， oscillatory or swinging. Even straight-line motion of the operating member is possible, though the term cam may not be considered properly applicable in such circumstances. Most text books on mechanics give some information on the design of cams and show examples of cam forms plotted to produce various orders of motion. Where neither the operating speed nor the mechanical duty is very high, there is a good deal of latitude in the nermissible design of the cam and it is only necessary to avoid excessively steep contours or abrupt changes which would result in noise, impact shock, and side pressure on the follower. But, with increase of either speed or load, much more exacting demands are made on the cam, calling for the most careful design and, at very high speed, the effect of inertia on the moving parts is most pronounced, so that the further factors of acceleration and rate of lift have to be taken into account and these are rarely dealt with in any detail in the standard text books. The design of the cam follower is also of great importance and bears a definite relation to the shape of the cam itself. This is because the cam cannot make contact with the follower at a single fixed point. Surface contact is necessary to distribute load and avoid excess wear, thus the cam transmits its motion through various points of location on the follower, depending on the shape of the two complementary members. The cams for operating i.c. engine valves present specially difficult problems in design. In the case of racing engines, both the load and speed may be regarded as extreme, because in many engines the rate at which the valves can be effectively controlled is the limiting factor in engine performance. In some respects, cam design of miniature engines is simplified by reason of their lighter working parts (and consequent less inertia) but on the other hand, working friction is usually greater and rotational speeds are generally considerably higher than in full-size practice. In the many designs for small four-stroke engines which I have published, I have sought to simplify valve operation and to provide designs for cams which can be simply and accurately produced with the facilities of the amateur workshop. Numerous engine designs which have been submitted to me by readers have contained errors in the valve gear and particularly in the cams and in view of prevalent misconceptions in the fundamental principles of these items, I am giving some advice on the matter which I trust will help individual designers to obtain the best results from their engines. There have been many engines built with cams of thoroughly bad design but which, in spite of this, have produced results more or less satisfactory to their constructors. It may be said that within certain limits of speed one can get away with murder but in no case can an engine perform efficiently with badly designed cams, or indeed errors in any of its working details. This article is concerned mainly with the design of cams for operating the valves of i.c. engines and, in order to avoid any confusion of terms, Fig. 1 shows the various parts of a cam of this type and explains their functions. The circular, concentric portion of the cam, which has no operative effect, is known as the base circle: the humy of the cam (shown shaded) is known as the lobe, and the flanks on either side rise from the base circle to the nose, which is usually rounded.Lift may be defined as the difference between the radius of the base circle and that of the nose. the anele enclosed between the points where the flanks join the base circle is termed the angular ‘period, representing the proportion of the full cycle during which the cam operates the valve gear. In Fig. 2, typical examples of cams used in i.c. engines are illustrated. The tangent cam, A, has dead straight flanks-which as the name implies form tangents to the base circle. This type of cam is easy to design and produce, the simplest method of machining being by a circular milling process forming a concentric surface on the base circle and running straight out tangentially where the flanks start and finish. It can also be produced by filing and I have in the past described how to make it with the aid of a roller filing rest in the lathe, in conjunction with indexing gear to locate the flank angles. Tangent cams can only work efficiently in conjunction with a convex curved follower, as this is the only way in which the flank can be brought progressively and smoothly into action. Some time ago an engine was described having tangent cams in conjunction with flat followers. This was not intended for extremely high speed and very likely produced all the power required of it, but it is quite clear that the flat face of the tangent cam. On engaging the flat tappet-over the full length of the flank all at once, must produce an abrupt slapping action which is noisy, inefficient and destructive in the long run. Rollers are often used as followers with tangent cams and are satisfactory in respect of their shape, but the idea of introducing rolling motion at this point is not as good as it seems at first sight, because it merely transfers the sliding friction to a much smaller area--that of the pivot pin. It is possible in some cases, however, to use a ball or roller race for the follower and this, at any rate, has the merit of distributing and equalizing the wearing surface. Tangent cams have been used with a certain degree of success for high-performance-engines and were at one time popular on racing motorcycle engines, though usually with some slight modification of shape-often “ designed ” by the tuner with the aid of .a Carborundum slip! Their more common application, however, has been on gas and oil engines running at relatively slow speeds, where they work well in contact with rollers attached to the ends of the valve rockers. Cams with convex flanks are extensively used in motor cars and other mass-produced engines. One important advantage in this respect is that they are suited to manufacture in quantity by a copying process from accurately formed master cams. The fact that hat-based tappets can be used also favours quantity production and they can be designed to work fairly silently. The contour of the flank can be plotted so that violent changes in the acceleration of the cam are avoided and, more important still, the tappet will follow the cam on the return motion without any tendency to bounce or float at quite high speeds. In such cases, it may be necessary to introduce compound curves which are extremely difficult to copy on a small scale, but cams made with flanks formmg true circular arcs will give reasonably efficient results, and are very easily produced in any scale: Concave-flanked cams. Comparatively few examples of concave-flanked cams (Fig. 2c) are to be seen nowadays, though they have been used extensively in the past with the idea of obtaining the most rapid opening and closing of the valves. Theoretically, they can be designed to produce consant-acceleration, but in practice they render valve control very difficult at high speed and their fierce angle of attack produces heavy side pressure on the tappet. The concave flank must always have a substantially greater radius than the follower, or a slapping action like that of a tangent cam on a flat follower is produced. The shape of the nose in most types of cams is dictated mainly by the need to decelerate the follower as smoothly as possible. It is one thing to design it in such a way that ideal conditions are obtained, and quite another to ensure in practice that the follower retains close contact with the cam. If the radius of the nose is too small, the follower will bounce and come down heavily on the return flank of the cam and,. if too great, valve opening efficiency will be reduced. Of the three types of cams, A, B and C, which all have identically equal lift and angular period, the lobe of B encloses the smallest area, and on first sight it might appear that it is the least efficient in producing adequate valve opening, or mean lift area, but owing to the use of a flat based tappet, its lift characteristics are not very different from those of a tangent cam with round-based tappet, and not necessarily inferior to those of a concave-flank cam. Unsymmetrical cams It is not common to make the two flanks of a cam of different contours to produce some particular result which the designer may consider desirable. In some cases, the object is to produce rapid opening and gradual closing, but sometimes the opposite effect is preferred. When all things are considered, however, most attempts to monkey about with cam forms lead to complications which may actually defeat their own object, at least at really high speeds. In many engines, particularly those of motorcycles, the cams operate the valves through levers or rockers which move in an arc instead of in a straight line, as in the orthodox motor car tappet. This may be mechanically efficient, but it modifies the lift characteristic of the cam, as the point at which the latter transmits motion to the follower varies in relation to the radius of the lever arm, (Fig. 3). With the cam rotating in a clockwise direction, the effective length of the lever will be greater in the position. A during valve opening than in position B during closing, as indicated by dimensions X and Y. This amounts to the same as using an unsymmetrical cam, and in the example shown, would result in slow opening and rapid closing of the valve, or vice versa if either the direction of rotation of the cam, or the relative “ hand ” of the lever, is reversed. The shorter the lever, the greater the discrepancy in the rate of movement, Neither the unsymmetrical cam form nor the pivoted lever is condemned as bad design, but I have sought to avoid them in most of the engines I have designed because they are a complicating factor in what is already a very involved problem, and by keeping to fairly simple cams and straight-line tappets, one can be assured that there are not too many snags. The employment of cams with flanks of true circular arc has enabled me to devise means of producing them on the lathe without elaborate attachments and, what is more important still, to produce an entire set of cams for a multi-cylinder engine in correct angular relation to each other by equally simple means. There is no doubt whatever that these methods have enabled many engine constructors (some without previous experience) to tackle successfully a problem which would otherwise have been formidable, to say the least. Many designers have attempted to improve valve efficiency by designing cams which hold the valve at maximum opening for as long a period as possible. This is done by providing dwell or, in other words, making the top of the lobe concentric with the cam axis over a certain angular distance in the centre of its lift. To do this, however, it is necessary to make the flanks excessively steep, thus producing heavy side thrust on the tappet, and making control at high speed more difficult, (Fig. 4A). A little consideration, however, will show that the same result can be achieved, with much less mechanical difficulty, by lifting the valve somewhat higher at an easier rate, as shown at B. This avoids the need for sudden acceleration and deceleration of the tappet and promotes flow efficiency of the valve. The shaded portions of the two cams show the differences in the area of the lobe, showing that nothing is really gained by the dwell. Factors in efficiency High valve lift is a desirable feature, but only if it can be obtained without making extra dificulties in controlling the valve. The maximum port area of a valve is obtained when the lift is equal to one-fourth of the seat diameter, but owing to the baffling effect on the valve head, a higher lift is better for flow efficiency-if it is practicable. Large diameter valves will obviously release and admit gas efficiently but they are more difficult to control and keep cool at high speed than smaller valves. Another point is that the exhaust valve is required to open against a high cylinder pressure, and the larger it is the more the load imposed on the cam, quite apart from the spring load. 凸輪設計的基本內容 如何為汽油發動機和其他機械設計和生產簡單而有效的凸輪 凸輪是被應用的最廣泛的機械結構之一。凸輪是一種僅僅有兩個組件構成的設備。主動件本身就是凸輪，而輸出件被稱為從動件。通過使用凸輪，一個簡單的輸入動作可以被修改成幾乎可以想像得到的任何輸出運動。常見的一些關于凸輪應用的例子有： ——凸輪軸和汽車發動機工程的裝配 ——專用機床 ——自動電唱機 ——印刷機 ——自動的洗衣機 ——自動的洗碗機 高速凸輪(凸輪超過1000 rpm的速度)的輪廓必須從數學意義上來定義。無論如何，大多數凸輪以低速(少于500 rpm)運行而中速的凸輪可以通過一個大比例的圖形表示出來。一般說來，凸輪的速度和輸出負載越大，凸輪的輪廓在被床上被加工時就一定要更加精密。 在多種機械裝置的操作中凸輪在某種形式下是必不可少。他們最有名的應用是在內燃機閥門操作裝置中，但在工業機器中，從印刷機到收割機械，凸輪機構也是一個相當重要的一部分。 一般來說，一個凸輪可以被定義為一個圓盤面或一個為產生接觸間歇往復運動的零件或從動件。大多數凸輪的運動是旋轉運動，但這不是一個必要條件，在特殊情況下，它的運動是半旋轉，振動或擺動。即使原動件可能是直線運動，但在某種情況下凸輪也可能會適當?shù)乇豢紤]，。 在機構學大多數文本書籍中給了關于凸輪設計和凸輪類型的實例設計的一些信息，產生各種規定的運動。在某種情況運行速度和機械的性能不是非常高，有一個規律是凸輪機構設計很好的協議，只需要避免過于陡峭的輪廓或從動件產生噪聲，影響沖擊，并側壓力的突然改變。 然而，凸輪速度或負荷增加或具有更嚴格的要求，尋求更精細的設計，并以極高的速度，在慣性運動部件上的作用最明顯，因此，對舉升的加速度和速度因素都必須考慮，這些很少在任何詳細的標準教科書中得到處理。 凸輪從動件的設計也是非常重要的，并且關系到凸輪自身的形狀。這是因?yàn)橥馆喤c從動件不能在一個固定點上接觸。表面接觸需要分配負荷，避免過度磨損，凸輪傳送運動通過從動件各點位置，這都取決于兩個互補零部件形狀。目前凸輪在發動機氣門設計的問題上特別困難。在賽車引擎中，無論是負載還是速度都可能會被視為極端，因?yàn)樵诤芏喟l(fā)動機中引擎的閥門上這些限制因素得不到有效控制。在某些方面，微型發動機凸輪的設計的簡化是由于他們的打火工作部件（以及隨之而來的慣量）的原因，但在另一方面，工作通常具有更大的摩擦和旋轉速度，一般都大大高于全尺寸的做法更高。 對于小型四沖程發動機的許多設計已經出版，我力求簡化操作閥門，并為凸輪可以簡單而準確地運用在業余設計制作車間的設施。許多發動機的設計已提交，讀者對設計中包含有錯誤的閥門裝置，特別是凸輪和這些項目上的基本原則有普遍的誤解，我給一些對此事的意見，而我的信任將有助于個別設計人員獲得其發動機的最佳效果。 目前有許多關于發動機的凸輪設計，盡管如此，這些設計結果或多或少令它們不滿意。可以說，它的速度在一定限度內可以滿足要求，但在某些情況下，凸輪設計不良可以與發動機配合，但在工作細節上會出現錯誤??。 本文關注的主要是集成電路的閥門發動機凸輪設計，并且為了避免一些混淆的術語，圖1顯示了這種類型的凸輪的各個部分，并解釋它們的功能。凸輪輪廓的同心部分，它沒有操作效果，被稱為基圓；凸輪（顯示陰影）被稱為葉輪，無論是從基圓上升到頂圓，這通常是圓形的側翼。 推程可以被定義為基圓半徑和頂圓之間的差值。點之間的封閉在兩側加入基圓的角被稱為周期，代表整個周期運作期間，凸輪齒輪比例閥。 在圖2中，對用于i.c.發動機凸輪典型例子進行了說明。切線凸輪，一個已經固定在直線兩側，其中顧名思義形式向基圓的切線。這種凸輪式很容易設計和生產，是由一個圓形銑加工過程形成了一個最簡單的方法，它是在表面與基圓同心連續運行了切向那里的兩翼開始和結束。它也可以產生和我在過去的描述如何與一個在軋輥車床休息備案，它借助與索引齒輪側面結合的角度來定位。 切線凸輪的有效工作只能和一個凸弧形上的從動件一起，因?yàn)檫@是唯一的方式，側面可以發揮作用，逐步平穩。前一段時間有一種引擎與切線凸輪一起被描述。這是不適合極高的速度的，極有可能產生力的集中現象，但相當清楚的是，它是切線凸輪的盤型平面。平面上推桿以上的側翼突然變長，運動中突然出現運動噪音，效率低，從長遠來看具有破壞性。 滾子經常被用來作為與切線凸輪的從動件，并在其形狀方面令人滿意，但在這一點上引入滾動運動的想法并不好??，因?yàn)樗坪跏且幌嗲樵福驗樗皇寝D(zhuǎn)移的滑動摩擦要小得多，即樞軸銷。然而，在某些情況下，有可能要使用一個球或滾子的比賽，對于這一點，無論如何，具有分布和均衡的磨損表面的優點。 切線凸輪已經使用于高性能型發動機的成功，在一定程度上，同一時間流行的賽車摩托車發動機，與一些形狀往往是“設計”所具有的援助略有修改，但通常調諧器，碳化硅流失了！然而，他們更常見的應用一直在天然氣和石油的發動機速度相對緩慢，他們?cè)谀睦锕ぷ鹘佑|良好，附著在滾筒的兩端閥門搖動運行引擎。凸齒面凸輪廣泛應用于汽車及其他大眾生產的發動機。在這方面的一個重要優勢是，它們適合于制造一個復制過程中形成的準確數量從主凸輪。在這頂帽子的挺桿可以使用的事實也有利于批量生產，他們可以設計相當默默工作。該側面輪廓可以繪制，使在凸輪加速度變化是避免突變，更重要的是，推桿將不能出現任何反彈或漂浮，在相當高的速度出現回復運動。在這種情況下，可能有必要引入一個小規模的復合曲線，但凸輪與兩翼圓弧會作出合理有效的結合，并且在任何規模很容易的產生凹陷。兩側凸輪的例子現在是比較少看到的，雖然他們已經在過去廣泛地使用，獲取最快速的開啟和關閉的閥門的方法。理論上，他們可以被用來產生永久的加速，但在實踐中非常高的速度和激烈的攻角時，閥門控制產生的側壓力使沉重挺桿困難。凹側面必須始終比從動件半徑更大，或者一個平面從動件切線凸輪產生左右運動。 ??大多數類型的凸輪，形狀主要是出于減速所需要的，盡可能的作平緩運動。這種設計方式可以認為理想的條件，在實踐中又是另一回事確保從動件保持密切與凸輪接觸。如果凸起半徑過小，從動件將會在凸輪側翼反彈和回落。如果過大，閥門開關效率會降低。 對凸輪的三種類型，A，B和C都具有相同的舉升和角度區間，B葉包圍面積最小，乍一看，它是可能出現的，它在產生足夠的閥門打開效率最低或平均升力面積，但是由于有挺桿的使用，其舉升特性并不十分明顯，不同于基圓的切線凸輪的挺桿，并不見得遜色于凹凸輪的側面。 非對稱凸輪 這是一種不常見的凸輪，利用不同的輪廓在凸輪兩側產生某種特定結果，這種考慮，設計者是可取的。在某些情況下，該對象產生迅速開放和逐步縮小現象，但有時相反的效果卻為最佳。然而，當所有的因素都考慮在內，大多數試圖與運動有關凸輪形式會引起并發癥，實際上可能失敗，至少在非常高的速度。 在很多引擎中，特別是摩托車，凸輪通過杠桿或在一個搖滾的操作，用一條直線代替圓弧運動，如正統汽車挺桿。這可能是改善機械效率，但它修改了凸輪的升降特征，當在某點上，后者傳遞運動給從動件和杠桿臂的半徑有關，（圖3）不同的凸輪升程的特性。隨著凸輪順時針?lè)较蛐D(zhuǎn)，杠桿的有效長度將會更大。 A位置開啟和B位置關閉閥門，用X和Y的尺寸來表示。與使用非對稱凸輪是相對等的，如這個例子所示，會產生緩慢開啟和迅速關閉的閥門的情況，或者相反，如果不論是凸輪的旋轉方向，或相同于“手”的杠桿的方向?qū)?huì)產生相反的效果。桿越短，運動速率的差異就越大，無論是凸輪機構的形式還是非對稱凸輪樞軸桿不好的設計，但我一直在努力避免在我所設計的引擎產生這種情況，因?yàn)樗麄兪且粋€(gè)非常復雜的問題，并保持相對簡單的凸輪和直線挺桿因素，人們可以放心，不會有太多的障礙。 對于具有圓弧面的凸輪的運用，使沒有詳細說明的情況下，車床生產它們的手段和方法，更重要的是，用正確的關系來生產多汽缸引擎的關系具有同樣簡單的方式。這些方法已使許多發動機構造（不含以前的一些經驗）成功地解決一個疑問，至少可以這樣說。 很多設計師都試圖改善凸輪的設計，以最大時間來提高閥門的工作效率。換句話說，使得耳垂超過一定在其升力中心的角距離凸輪軸同心的頂部。但是要做到這一點，有必要作出過度陡峭的側面，從而產生大量的挺桿側向推力，在高轉速時，使控制更加困難。 然而幾乎沒有考慮，同樣的結果表明，這種方法是可以實現的，出現很少的機械問題，解除閥也更容易效率也更高，如B所示。這避免了推桿突然加速和減速，并促進流動閥門的工作效率。兩個凸輪的陰影部分顯示了葉面積的差異，顯示出真正的高效性。只有在不進行額外的控制時，氣門的高效升程是非常理想的，閥門的最大開口區，等于閥座直徑的四分之一，但是由于對閥頭莫名其妙的影響，如果它是可行的，較高的升程流動效率將會更好。 大口徑閥門能夠很明顯釋放和有效得承載，在高速運動下比小閥門更難控制但他們更難以控制。另一點是，排氣閥對高壓缸做出反抗，凸輪上的外加荷載越大反抗就越大，完全不同于彈簧負載。 7